When installing a weight distribution system on a vehicle with self leveling suspension such as your 2008 Cadillac Escalade you will want to hook the trailer up to the vehicle first and let the suspension level itself out before you do the initial setup. This way the WD system will be set up properly for how the vehicle will be when the vehicle is being used. view full answer...
I attached an install video and installation instructions for the install harness part # 3016 that is recommended for installing the Prodigy P3 Brake Controller part # 90195 that you referenced. view full answer...
For your Equal-i-zer Weight Distribution System w/ 4-Point Sway Control # EQ37040ET since your tray is right at that 25-32 inches back from the center of your coupler where your brackets need to be, the best solution to use this system is to drill into your frame and directly mount your brackets to the frame at the height you need. This may require modifying the height of your brackets depending on your tray and tank fit. view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2" # C15324 will not require any trimming or cutting to install. The installation is not difficult for this hitch and the bumper already is shaped in the hitch location. The only thing you need to do is lower and remove the spare tire and then reinstall after installation. I've attached the installation details to assist. view full answer...
I spoke with my contact at Hopkins regarding your newly installed Impulse model 47235 brake controller and he said that on this particular unit there won't be any lights when stepping on the brake controller if you're not hooked up to a trailer. He did mention, like you did, that on previous generation controllers there would be a light or number displayed when applying the brakes whether connected to a trailer nor not but that is not the case with the Impulse.
It sounds like the brake... view full answer...
It is fine to use electric brakes on a boat trailer, just be sure to unplug them before hitting the water.
In regards to a brake controller, vehicles with factory 7-ways do not have brake controllers integrated in them and you will need one if you have electric brakes. There may be a harness that allows you to simply plug the controller in and use it without difficulty. If you let me know the year, make and model of your vehicle I can tell you if there is a fit for a plug-and-play brake... view full answer...
Depending on how you install the Curt Front Mount Trailer Hitch Receiver # 31302 will determine if you need to trim the front fascia.
This front mount hitch is a high/low hitch that can be installed with the hitch opening on the top of the cross member or below it.
If you choose to install the cross member with the hitch opening below the cross member you will not need to trim anything. If you want the additional ground clearance of having opening above the cross member then you will... view full answer...
Good question, and a 2012 Cadillac Escalade does not have a harness that will allow you to plug in a brake controller, but it does have the wires already run under the dash, regardless of if you have the factory 7-way or not. If you take a look at the accompanying photo you can see where the wires will be; this is a cut out from the linked installation video of the Tekonsha Primus IQ Trailer Brake Controller # TK90160. This is from a 2009 Cadillac Escalade which is the same generation as... view full answer...
Thanks for the purchase of the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136, and the answer to your question is if you do not want to use the OneControl Touch Panel you certainly don't have to. This is only compatible with trailers that have the OneControl feature installed so it does have to - and will - work with just the touchpad if that's what you'd like to use.
I've added links to a video review and install for you to check out of this system... view full answer...
The brake controller connection is in the same spot as found in the Suburban or the GM full sized trucks of that generation. It's located in a junction box behind and to the right of the emergency brake pedal. You'll need to remove the cover, and plug the connector into the socket shown in the provided photo.
If you'll be installing the Tekonsha Prodigy P2 Trailer Brake Controller # 90885 you'd looked at, you'll need the # 3016 Brake Controller Wiring Harness. I've linked to a video showing... view full answer...
There is no brake controller plug-in port on your 2009 Escalade but the wiring is present under your dash to the left of the brake pedal.
I have attached a link to an installation video of a brake controller on a 2009 Escalade you can check out. Just go to about the 1:40 mark on the video and it shows where the wiring can be found and how to complete the brake controller installation. The wiring harness is about 4 inches behind the onboard diagnostic port. There will be a piece of white... view full answer...
I do not think you will have a problem carrying your 66 lb ebikes on the Thule EasyFold XT Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches - Frame Mount, part # TH903202, provided you follow this piece of advice. Now this advice is not from me, but from ebike manufacturers speaking about the best way to transport their bikes on your vehicle. You should always remove your batteries from your bike when transporting them on a bike rack. If you follow that advice you will not have to... view full answer...
From the picture you provided, I can say that you are almost there. The Tekonsha Plug-In Wiring Adapter # 3016. I included a picture for you to check out, but it's actually the port directly above the white one with the blue housing on the left hand side. It looks like it will be a snug fit, but wont cause any issues. I included an install video for you to check out, but it is on a Silverado and it didn't have that blue and white plug, but should still help. view full answer...
The bolt for the Timbren Rear Suspension Enhancement System # TGMRYS4 simply connects the spring to the disc which fits into the rear suspension cup on your 2011 Cadillac Escalade. The bolt will not thread into any part of your Escalade. They use this setup as it will allow you to add a Spacer # TA25722-90P00 between the spring and cup in the event you are still experiencing more sag than you would like. view full answer...
I contacted the manufacturer, Edge, about the EvoHT2 Hand-Held Performance Tuner # EP26040 that works with a 2002 Cadillac Escalade and if your car has the 6.0L V8, along with the pre-loaded performance and economy tunes, here are the parameters that it can affect: Data Logging, Calibrate Speedometer for Gear Ratio, Calibrate Speed for Tire Size, Cooling Fan Control, Top Speed Limiter, Rev Limiter, Shift Points, Shift Firmness.
In regards to what it tunes to make power gains, I was told... view full answer...
If your 2007 Cadillac Escalade has a factory 7 pole plug, the Redarc Tow-Pro Elite Trailer Brake Controller - 1 to 3 Axles - Proportional Item # RED44FR can be wire directly into the factory wiring located under the dash, just to the left of the steering column. The wiring may be taped up to other wiring. The wiring you are looking for will be 4 wires with taped ends. Red, Black, White, Light Blue with a White stripe.
Determine where you want to mount the brake controller knob on the dash.... view full answer...
If your Tekonsha Prodigy P2 Trailer Brake Controller # 90885 has numbers scrolling on the display when it is not connected, it seems likely you have some sort of corrosion on the brake output circuit of your 2011 Escalade's 7-way. It would seem that the brake controller thinks that your trailer is still connected, which would explain the numbers.
I recommend removing the connector from the socket of your 7-way and cleaning the pins to see if that does the trick, and a replacement 7-way... view full answer...
First check the instructions of your current weight distribution (WD) system as well as the owner's manual for your 2007 Cadillac Escalade. Some WD systems are not rated to work with air bags on a vehicle and some vehicles do not allow the use of a WD system.
If both permit the use of the other then the next step would be getting both systems to work together. I spoke with my contact at Reese about how to get this to work with their Strait-Line Weight Distribution System # RP66074 and... view full answer...
It is normal for the Tekonsha Prodigy P3 # 90195 to be on even when your 2008 Cadillac Escalade is turned off, and it goes into sleep mode after 15 minutes of not sensing movement to preserve your battery.
The reason for it always being on is that's how it saves your preset settings, if it was turned off/unplugged each time the vehicle was turned off you would need to setup the controller each time.
I included a video of the # 90195 for you to take a look at. view full answer...
Go To Results