Lippert Outriggers for Manual RV Steps

See what our Experts say about this Lippert Accessories and Parts

• Will Flexco Manual Pull-Out Steps for RVs # SMFP-4400 Fit 2005 2005 Crossroads Cruiser
  The Flexco Manual Pull-Out Steps for RVs # SMFP-4400 that you referenced will fit your 2005 Crossroads Cruiser but at worst might require moving the current brackets, or going a different route all together. You could weld these directly to your trailer frame, or use outriggers # LC301704 to act as new brackets. The mounting bracket dimensions of this are 28-1/8" wide x 18-1/2" tall x 12" deep.
  view full answer...
• Triple Step Recommendation for a 2010 Springdale SRT
  The Triple Step part # LC432687 would work for you and could potentially install pretty easily depending on where you measured the distance between the mounting brackets. I attached a picture and a set of installation instructions that have the dimensions of this step listed for you to check out. You may already have outriggers installed on your 2010 Springdale SRT, but if not you would want the part # LC301704. I also attached a couple helpful videos for you to check out as well.
  view full answer...
  
• Can 28 inch Wide 4-Step RV Steps Replace 27-1/2 inch Steps on RV
  The RV steps do get a bit wider as you add more steps to them. The closest option we have is the Alumi Tread part # LC432698 that you referenced which would be 28 inches wide. For basically all RV applications you can still install the steps but you'd have to move the brackets out or remove and install new ones. For new brackets we have the outriggers part # LC301704 which would work well.
  view full answer...
• Replacement Mounting Bracket Recommendation for RV Steps
  Sounds like the outriggers are what you need to replace. For that we have the # LC301704 which we recommend when people are installing new trailer steps.
  view full answer...
• How Can I Determine Which RV Steps Are Needed For My 2018 Keystone Passport Ultra Lite Express TT?
  In order to determine if the Kwikee Electric RV Step Complete Assembly - Double # LC372261 will work with your 2018 Keystone Passport Ultra Lite Express TT or not, you will need to locate the space available underneath your trailer that lines up with the doorframe, and measure the width and depth. You're going to need a mounting space that is at least 25-1/2" wide and 11-3/8" deep. If you have less or more space available beneath your doorway, then check out the list attached that shows...
  view full answer...
  
• Is There a 3 Step RV Pull Out Step that Can Replace LC432682
  There are 3 step pull out kits similar to the # LC432682 that you referenced but they are wider across the board so the exact mounting hardware you are using now won't work. The part # LC432690 would be a great solution for what you have but it's 27-1/2 inches wide and what you have now is 2 inches narrower. For new brackets you'd also want the part # LC301704.
  view full answer...
• Can Lippert Manual Pull-Out RV Steps Be Added To A 2022 Coachmen Apex Nano Off-Grid 194BHS
  Since the Coachmen Apex Nano Off-Grid 194BHS is designed with fold-down steps instead of the traditional pull-out steps like you're looking at you would have build a mounting bracket for the steps to mount onto. Outriggers # LC301704 could be used but you need to make a solid connection to the frame otherwise there's a good chance the steps could fall off as you using them. You'll most likely want to contact a local fabricator and have them weld the mounting brackets on to ensure your...
  view full answer...
• Mounting Bracket Dimensions of Manual Pull-Out Step
  The Manual Pull-Out Step for RVs - Double # LC432682 has mounting holes that are about 24" x 7" and although there are not any with a 14" x 7" pattern, you can still use this step. In order to do so you have a couple of choices. The first would be to weld the steps onto your RV while the other option would be to use Lippert Outriggers for Manual RV Steps # LC301704. You would need Mounting Hardware # LC118155-72 to attach the steps to the Outriggers.
  view full answer...
• Can Electric Motorhome Step Be Replaced By 3-Step Manual Step
  You absolutely can replace powered RV steps with manual steps to save yourself the headaches of wiring issues, bad motors and also to reduce the number of devices that put demands on your motorhome's power system. Our range of 3-step manual pull-out steps is shown on the linked page. Motorhomes typically use a 24-inch size step but we do also have a 25-inch model # LC432690. What you'll want to do is measure the size of the mounting bracket on your original part. For a great value I really...
  view full answer...
• How To Confirm Fit Of the Alumi-Tread Manual Pull-Out Steps On a Camper
  The Alumi-Tread Manual Pull-Out Steps part # LC432698 are designed for a mounting bracket 28" wide. In order to confirm fit you'd need to measure the exiting mount bracket. If it does not match you could make them compatible with new brackets, the Lippert Outriggers for Manual RV Steps part # LC301704 or you could go with another option that better closely matches what you have on the trailer now. I unfortunately would not have any information about the mounting brackets on any one particular...
  view full answer...
• Manual Pull Out Steps Fit and Outrigger Solution for Different Bolt Pattern
  The Flexco Manual Pull-Out Steps for RVs - Triple - 8" Drop/Rise - 24" Wide - 350 lbs # SMFP-3100 may fit your 2007 Discover 31LKTG, but the only way to know for sure is to do some measuring. The mounting base is the part that needs to fit in your access space and is 28-1/8" wide x 9-3/4" deep. This step has a bolt pattern of 25-3/8 inches wide and either 5-1/2 inches deep or 7 inches deep depending if you use the second or third mounting holes. If that bolt pattern doesn't match up,...
  view full answer...
• Determining if Lippert Alumi-Tread Manual Pull-Out Steps # LC432698 Will Fit Keystone Montana
  The Lippert Alumi-Tread Manual Pull-Out Steps # LC432698 referenced in your question may work well on your 2017 Keystone Montana High Country. In order to verify that they will install perfectly in place of your existing assembly you will just need to take a couple of measurements. Trailer manufacturers do not typically do a good job of maintaining detailed specs on items like these so I was unable to verify the type and size of the assembly that is currently installed on your Keystone...
  view full answer...
  
• Do Lippert Double Steps Fit Same Brackets as Lippert Triple Steps
  The 3 step versions of the Lippert steps like the part # LC432687 are wider than most of the 2 steps like what you have. The difference in width is not unusual unfortunately. What you can do is move your current brackets out or remove them and use the outriggers # LC301704.
  view full answer...
• Pull Out Triple Step Setup for Forest River Rockwood
  The mounting bracket width of the Triple Flexco Manual Pull-Out Steps # SMFP-3100 is 28-1/8 inches. If your bracket with is 27 inches you'd need to have them removed and install wider outriggers with the part # LC301704. If you need a narrower step setup overall the # LC432696 is 27-1/2 inches or the Torklift GlowStep part # TLA8103 is 25-1/2 inches overall in width.
  view full answer...
• Lippert Outriggers For Lippert, Stromberg Carlson Or Hickory Springs Manual Steel Pull-Out Steps
  I believe the mounting brackets you're looking for, is the Lippert Outriggers for Manual RV Steps # LC301704 which will help you install your manual or RV steps on your RV. This works with Lippert, Stromberg Carlson, or Hickory Springs manual steel pull-out steps, and Lippert Tread Lite manual steps.
  view full answer...
• Replacement Double Step Recommendation for Coleman 17 ft Camper
  At one point the Flexco Steps part # SMFP-2100 that you referenced were listed as having the same width you need of 26-1/8 inches between the mounting brackets. We now know that the dimension is really 27-5/8 inches. Since we don't have a step that matches directly you'll either need to move your current brackets or have new ones installed with the Outriggers part # LC301704. The steps of this kit have an 8 inch rise whitch is pretty standard and would be a great option.
  view full answer...
• Availability of Scissor Steps That Mount Underneath the Camper
  The mounting bracket on the Brophy Aluminum Scissor Steps, part # AS24, is 25 inches long and 1-1/2 inches wide and should be placed 1/8 inch below the lowest part of the door on your RV for installation. The steps I have that are made to bolt or weld onto the trailer frame are the Stromberg Carlson brand. They will only have single, double, and triple steps. I am including a link to a product page that will list all of the Stromberg Carlson steps I have available. I also have the Outriggers...
  view full answer...
• Mounting Methods for UWS Underbody Aluminum Trailer Toolbox UWS04012
  The UWS Underbody Aluminum Trailer Toolbox # UWS04012 does not include any mounting hardware since it is a general-purpose product. So you'll determine the best installation method for your preferred mounting point on your specific trailer. The amount of weight you'll load into it should be taken into account as you determine the mounting location and method of attachment. The box itself weighs about 50-lbs. You might use L-brackets like # CE10211G, if you don't mind drilling into the...
  view full answer...
  
• Triple Steps that Can Fit 2010 Forest River Georgetown
  The great thing about RV steps like the triple step part # LC432690 is that they are universal enough in how they install that they can basically be made to fit any RV including your 2010 Forest River Georgetown. At worst you might have to move the mounting hardware you have now or have these steps welded in place but they will fit your motorhome. If you wanted to install new mounting brackets you'd then need the part # LC301704.
  view full answer...
• Recommendation For Adding A Two Step Manual Step To 1989 Honey RV
  The Lippert Manual Pull-Out Step for RVs - Double - 7" Drop/Rise - 24" Wide - Steel - 300 lbs # LC432682 are a great option for your 1989 Honey RV. I recommend using the Lippert Outriggers for Manual RV Steps # LC301704 to give more stability to the mounting of these steps. You can use the Mounting Hardware for Lippert Electric and Manual RV Steps # LC118155-72 for this installation.
  view full answer...
• Can New RV Steps Install On RV Where Old Brackets are Different Dimensions
  When changing the amount of steps you have on an RV like with the # SMFP-3100 it's pretty common that the widths of the brackets don't match up perfectly, but the good news is you can still install a different set as long as you are willing to make some modifications. What you can do is see if you can move the brackets you have now, weld the steps directly to the frame, or also you could go with new outriggers like part # LC301704 to replace what you have.
  view full answer...
• Key Dimensions for Selecting Replacement Triple Step Unit for Jayco Travel Trailer
  Your photo did not make it through to us but we can still help you select replacement steps for your Jayco Jay Flight 28BHStravel trailer. The RV steps we offer for towable trailers come in several overall widths. You can see all sizes and models on the page I linked for you. You will want to match the overall mounting pattern of the new step to your existing unit. You will also want to ensure the new step unit does not reduce your ground clearance; keep the existing step's retracted height...
  view full answer...
• What Do the Lippert Outriggers part # LC301704 Do
  Yes, the Lippert Outriggers part # LC301704 are exactly what you described. These attach to the bottom of the trailer frame and provide brackets for the RV steps to attach to.
  view full answer...
• Are New Mounting Brackets Required to Install Double Step on RV in Place of Single Step
  The single step RV steps do have smaller mounting dimensions so if you are wanting to go with a double step to replace what you have what you'd need is the Lippert Manual Pull-Out Steps # LC432682 which is a double step that has a foot plate that provides solid traction. Since the mounting brackets of your RV are going to be too small you'll need outriggers too to go with this as part # LC301704 and you'll be set.
  view full answer...

Do you have a question about this Accessories and Part?