2019 Ram ProMaster 2500 Trailer Hitch Installation And Review Videos

Curt Trailer Hitch Installation - 2019 Ram ProMaster 2500- Video

Today on our 2019 Ram ProMaster 2500, we're going to be taking a look at and showing you how to install the Curt class III custom fit trailer hitch receiver.Here's what our hitch is gonna look like once we have it installed. The cross tube's going to be hidden behind the bumper, and all we're going to see is that receiver tube sticking out. As you can see, our hitch is going to stick out just past our bumper, but not enough to where it's going to cause a hazard when we're walking behind it. It is a class III hitch, which means it's going to give us that two inch by two inch receiver tube opening and have a really wide variety of options when it comes to accessories.Now, the way we're gonna mount any of those accessories is to the hitch pin hole here on the side. It is going to accept a standard five ace pin and clip. Now, these aren't included with the kit, but you can pick them up here etrailer.com, along with some locking devices to keep your accessories secure.Now, if you do plan on doing some towing, our safety chain loops are going to be a plate style, but they're going to be in the vertical position, which means we're not going to have to worry about interference from our hitch pin or locking device, and you can see that we have plenty of room to get most size hooks on or off.As far as the weight capacity goes, our hitch is going to have a 500 pound tongue weight, which is the maximum downward force of the receiver tube, along with a 5,000 pound gross trailer weight rating. more

2/20/2019 2:47:10 PM

Draw-Tite Max-Frame Trailer Hitch Installation - 2019 Ram ProMaster 2500- Video

Today on our 2019 Ram Promaster 2,500 we're going to be taking a look at and showing you how to install the Draw-Tite class three custom fit trailer hitch receiver. So here's what our hitch is going to look like once we have it installed. The cross tube is going to sit right below the bumper, but the main thing we're going to see is that receiver tube sticking out. It's a class three hitch, means it's gonna give us that two inch by two inch receiver tube opening. So I'll have a really wide variety of options for any kind of accessory for when I mount up.The way we're going to mount any of our accessories, the hitch pin hole here on the side. It's gonna accept a standard five ace pin and clip. more

2/15/2019 4:13:15 PM

Draw-Tite Max-Frame Trailer Hitch Installation - 2019 Ram ProMaster 2500 76050- Video

Today on our 2019 Ram ProMaster 2500 we're going to be taking a look at and showing you how to install the Draw-Tite Class 3 Custom Fit Trailer Hitch Receiver.So here is what our hitch is going to look like once we have it installed. The cross tube's going to be hidden behind the bumper and all we're going to see is the receiver tube sticking out.Now, our receiver tube is going to stick out just a little bit past the bumper but not so much that we're going to have to really worry about it unless we're right up against the bumper walking by.Now this is a class three hitch which means it's going to give us a two inch by two inch receiver tube opening and they have a lot of different variety of accessories that are going to be available.The way we're going to mount any of those accessories is through the hitch pin hole here on the side. Our hitch is going to accept a standard 5/8th's pin and clip. Now these aren't included, but you can pick them up here at eTrailer.com.Now the smaller hole is towards the opening on the receiver tube, that's going to be exclusively for the J-Pin Stabilization Device. Now the way this is going to work, the long threaded section will go into our hitch pin area and then this hook is going to come into that secondary hole and it's going to apply pressure to our accessory. We'll tighten it up using the included nut and it will keep all that rattle and play and noise out of our accessory when we're driving down the road. more

2/15/2019 4:07:12 PM