bing tracking image

2014 Jeep Wrangler Unlimited Hitch Bike Racks Installation And Review Videos

     

Thule Helium Aero Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited- Video

Thule Helium Aero Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited

So we have our 2014 Jeep Wrangler. We're going to be testing the Thule helium aero. This is a folding and tilting 2-bike rack. It's designed for use in both inch and 1/4 and 2-inch hitches. It's part number is TH9042. Now to begin the test fit, we're going to slide the shank of the bike rack right into the receiver tube of our hitch. As we do, we'll hold out on the attached pin, line up our pinholes, allow that pin to go into the hole and I always like to pull back slightly on it just to be sure we give ourselves as much clearance room as we can. more


Watch Video

2/11/2015 3:41:36 PM



Swagman Titan Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited- Video

Swagman Titan Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited

Today on our 2014 Jeep Wrangler Unlimited we're going to be test fitting this Swagman Titan. This is a folding and tilting 4 bike rack. It's designed for use with both the 1-1/4" and the 2" hitches. Its part number is S63410. To begin our test fit we're going to slide the shank of the rack right into the receiver tube of our hitch. As we slide it in we want to line up our threaded hole with our hitch pin hole. We'll then thread in our anti-rattle bolt and tighten it down with our wrench. more


Watch Video

2/11/2015 3:28:51 PM



Yakima FullTilt Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited- Video

Yakima FullTilt Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited

Today on our 2014 Jeep Wrangler Unlimited we're going to be test fitting the Yakima Full Tilt. This is a folding and tilting four bike-style rack. It's designed for use in the 1-1/4 and 2 inch hitches. It's part number is Y02462. To begin our test fit we're going to slide the shank of the rack right into the receiver tube of our hitch. We want to make sure that our silver anti-rattle device slides in and we'll watch for the small silver pin to pop out in our pin hole just like that. I like to pull the rack back at that point just to give us as much clearance room as there is available. more


Watch Video

10/22/2014 4:04:19 PM



Saris Freedom SuperClamp Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited- Video

Saris Freedom SuperClamp Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited

Today on our 2014 Jeep Wrangler Unlimited we're going to be test fitting the Saris Freedom Superclamp 2-bike platform-style rack designed to fit 1-1/4" and 2" hitches, part number SA4025. We're going to begin our test fit by sliding the shank of our bike rack into the receiver tube of our hitch. As we slide this in there we'll want to keep an eye out for our pinholes to line up with each other. Then we'll take our anti-rattle bolt and thread it through, making sure we start here on the driver side and go through to the passenger side. Once we get the anti-rattle bolt finger tight we can then use a wrench or socket wrench to finish tightening it all the way down. With this bolt tight it's really going to help take out any rattle or wobble that we may have inside of our hitch. more


Watch Video

10/15/2014 5:03:46 PM



Saris Bike Porter Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited- Video

Saris Bike Porter Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited

Today on our 2014 Jeep Wrangler Unlimited, we're going to be test fitting the Saris Bike Porter 4-Bike Rack for 1-1/4 inch and 2 inch hitches, part number SA404B. We're going to begin our test fit by sliding the shank of the bike rack into the receiver tube of our hitch. As we slide it in there, we'll go ahead and look for our pinholes to line up with each other. Then we can take our anti-rattle bolt and install it from driver's side to passenger side. Then we can just thread it through. Once we get this hand tight, we'll just use our socket wrench to secure it all the way down. With it fully tight, it's really going to help eliminate some rattle and wobble that we may have inside of our hitch. We'll simply just install the clip on the other side, and then we can go over some measurements. This bike rack is going to give us a ground clearance of about18-1/4 of an inch. The closest point of the bike rack to the rear of our vehicle is just going to measure the mass here at the top. more


Watch Video

10/15/2014 10:30:00 AM



Saris Freedom Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited- Video

Saris Freedom Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited

Today on our 2014 Jeep Wrangler Unlimited, we're going to be test-fitting the Saris Freedom 4-Bike Rack. This is platform, solid hitch-mounted rack. Part number SA4414B. We're going to begin our test fit by sliding the shank of our bike rack into the receiver tube of our hitch. As we slide it in, we want to keep an eye out to make sure that our pin holes are going to line up with each other. Once we get those in line, we can take our anti-rattle bolt. more


Watch Video

10/14/2014 10:16:16 AM



Thule Vertex Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited- Video

Thule Vertex Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited

Today on our 2014 Jeep Wrangler Unlimited we're going to be test fitting the Thule Vertex. This is a folding and tilting 4-bike rack. It's designed for use in both the 1-1/4" and 2" hitches. Its part number is TH9029. Now to begin our test fit we need to slide the shank of the rack right into the receiver tube of our hitch. As we do this we'll line up the threaded hole with our hitch pinhole. more


Watch Video

9/25/2014 9:27:40 AM



Thule Hitching Post Pro Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited- Video

Thule Hitching Post Pro Hitch Bike Racks Review - 2014 Jeep Wrangler Unlimited

Today on our 2014 Jeep Wrangler Unlimited were going to be test fitting the Thule Hitching Post Pro. This is a folding and tilting four bike rack. Its designed for use on both the 1-1/4 and 2 inch hitches. Its part number is TH934XTR. Now to begin our test fit we need to slide the shank of the rack into the receiver tube of our hitch. As we slide this in well line up our pin hole, our threaded hole with our hitch pin hole. Well take our anti-rattle bolt and well thread that in. more


Watch Video

7/7/2014 1:15:57 PM



  1