Trailer Wiring Harness Installation - 2016 Chevrolet Equinox- Video

Speaker 1: Today on our 2016 Chevrolet Equinox you're gonna be taking a look at and I'm gonna show you how to install the T-1 Vehicle Wiring Harness with Four-Pole Flat Trailer Connector, Part number 118494. This is gonna give you all the proper lighting function you need for your trailer, your brake lights, your running lights, and both of your right and left turn signal, along with the ground. It's also gonna come with a attached dust cap. What that's gonna do is it's gonna help protect your connection from corroding. It's gonna help keep debris and moisture out. As far as the installation goes, it is fairly simple and straightforward. more

Watch Video

7/31/2018 1:32:11 PM

Trailer Wiring Harness Installation - 2016 Chevrolet Equinox 118264- Video

Today on this 2016 Chevrolet Equinox, we're going to review and install the T-One Vehicle Wiring Harness for the Factory Tow Package from Tekonsha, part number 118264. We just pull out what we need, put the floor panel back into place, and pull out our wire. Our door seal's thick enough when we shut it, it's not going to hurt the wire and we just run out whatever length we need out to your trailer at this point. Now, when you shut the gate, make sure that this is no where near the latch because you'll cut the wires and you'll be starting over. Just pull out a little bit right here. We can go ahead and shut our hatch and pull out what we need to go out to our trailer. As you can see, we have plenty to reach down to our hitch here and our trailer should have plenty of lead with it to match up to this. When we're finished towing for the day, we can go ahead and hide it back inside and be one less item hanging out below your vehicle. This is your 4-pole flat wire harness right here, with it's own built-in cover. more

Watch Video

1/19/2017 10:59:48 AM

Trailer Wiring Harness Installation - 2016 Chevrolet Equinox C56210- Video

Today on this 2016 Chevrolet Equinox, we're going to review and install a Curt T-Conductor Vehicle Wiring Harness for the factory tow package, part number C56210. All right, now, when you're ready to use it, just open up the floor panel and pull out the wire harness. Put the panel back into place. It's not going to hurt anything. Then, run your wire harness to the outside. Just make sure you stay away from the latch, so when you close the hatch on it, it won't damage the wires. Then, after it's shut, you can pull out what you need to go to down to your trailer hitch and meet up with your trailer. You can see we have plenty of length to go down to your trailer hitch and meet up with your trailer. You got the wire harness itself. more

Watch Video

1/19/2017 10:59:34 AM

Best 2016 Chevrolet Equinox Trailer Wiring Options- Video

Today on our 2016 Chevrolet Equinox we're going to be taking a look at the best wiring options available. The two wiring options we're going to be taking a look at are the CURT T-Connedctor, and that's part number 56094. The second one is going to be the Tekonsha T-One Connector. That's part number 118494. Both are going to provide you with a four-pole flat connector for your trailer wiring at the rear of the vehicle. The main differences between the wiring harnesses are the Tekonsha here uses a power module. What this does is it connects directly to your battery, copies the signal to your trailer wiring, and prevents overloading your car's electrical system. more

Watch Video

1/19/2017 10:59:24 AM

Trailer Wiring Harness Installation - 2016 Chevrolet Equinox 56094- Video

Today on our 2016 Chevrolet Equinox we will be taking a look at and installing the CURT T-connector Vehicle Wiring Harness for a 4-Pole Flag Trailer Connector, part number 56094. Here's what our 4-pole wiring harness is going to look like once it's installed on the back of our vehicle. Now this is going to be quite essential to anybody that wants to have lights that operate on their trailer. Using a 4-pole trailer connector, you can simply hook up those lights. You'll have a tail light, both left and right turn signals, as well as running lights with the set up. First thing we'll do is test our wires is to remove the cover then we'll connect our ground, and then we'll test out our brown wire which will be our tail lights. Now we'll go ahead and test out our yellow wire which will be our left turn signal and our green wire which will be our right turn signal. Now for the brake lights, which will be both our green and our yellow. more

Watch Video

2/10/2016 2:18:47 PM

  1