Trailer Wiring Harness Installation - 2011 Chevrolet Equinox- Video
Speaker 1: Today on our 2011 Chevrolet Equinox, we're going to be taking a look at and I'm going to show you how to install the Hopkins plug-in simple vehicle wiring harness with four pole flat trailer connector, part number HM11141275. This is what our four pole plug looks like when it's installed. It's going to give you all the proper lighting functions for your trailer; your running lights, brake lights, and both turn signals, along with your ground.It's also going to come with a nice dust cap that's going to help protect any of your connections, keep them from corroding, getting any dirt, grime, or any moisture on them. When not in use, our dust cap can double as a holder to keep our wire from dragging on the ground. It is a very simple installation. Remove your taillights, you plug it into the existing wiring, run your four pole down to the back here, and you're ready to go. more
8/9/2018 2:02:37 PM
Best 2011 Chevrolet Equinox Trailer Wiring Options- Video
Today on our 2011 Chevrolet Equinox we're going to be taking a look at the best wiring options available. The two wiring options we're going to be taking a look at our the CURT T Connector, and that's part number 56094, and the second one is going to be the Tekonsha T1 Connector, and that's part number 118494. Both are going to provide you with a four-pole flat connector for your trailer wiring at the rear of your vehicle. The main differences between the wiring harnesses are the Tekonsha here uses a power module. What this does is it connects directly to the battery, copies the signal to your trailer wiring, and prevents overloading your car's electrical system. The CURT wiring harness is just going to connect within our taillights and won't offer you the same protection. Because the CURT wiring harness doesn't have a power module the installation is going to be quick and easy, and you'll be on the road in no time. more
1/19/2017 10:58:59 AM
Trailer Wiring Harness Installation - 2011 Chevrolet Equinox 118494- Video
Today on our 2011 Chevrolet Equinox, we're going to be installing the Tow Ready T-One vehicle wiring harness with the 4-pole flat trailer connector, part number is 118494. Here's what our wiring kit is going to look like. You can see we've got a yellow and brown wire. It's going over to the driver side. They got the T-connector, you see we've got an in-line connector right here, will separate the light, plug it in either side of the factory connection. Do that on both sides. The green one, single green wire that goes over to the passenger side, and this is what we're after. Of course, that's the 4-pole wiring. more
3/26/2015 2:50:51 PM
Trailer Wiring Harness Installation - 2011 Chevrolet Equinox 118264- Video
Today on this 2011 Chevrolet Equinox. We're going to install part number 118264 from Tow Ready. Okay, the wire install inside the car, so we need top open up the back hatch to get access to it. We'll also have to remove the floor covering, and this panel right here needs to be removed. Steady pressure pulling up shouldn't snap it. Set that to the side. Next we'll go ahead and remove this tie down points right here to give us some extra room. more
8/21/2014 12:16:01 PM
Trailer Wiring Harness Installation - 2011 Chevrolet Equinox 56094- Video
Today on our 2011 Chevy Equinox, we'll install the Curt T-Connector 4-pole Wiring Harness, part number 56094. First, we'll open up the rear cargo door and then we'll remove the driver's side tail light assembly. To remove the tail light assembly, we'll remove the two fastener caps and set them aside and then remove the two fasteners. Now, we'll simply remove the rear tail light assembly by gently prying and pulling on the tail light assembly until it pops free from its alignment fasteners. Be careful not to break these alignment tabs as you remove it. Now, we can go ahead and remove the manufacturer's wiring from the tail light assembly. more
11/19/2012 1:38:28 PM
