Roadmaster Single Park Light Diode Installation - 2012 Jeep Grand Cherokee- Video
Today on our 2012 Jeep Grand Cherokee we're going to be showing you how to install the Roadmaster Single Park light Diode that's used on the charge wire. Part number is RM-690. If we've got 12 volt power at the 7 pull in the back of our motor home we can actually use that power to trickle charge the charging system that's in our vehicle. Now to connect to our Park Light Diode we need to run a 12 volt wire from our plug in here at the front of the vehicle on back to where we'll eventually mount the diode closer to our 12 volt power connection source. We just run it kind of through the front of it here just so you have enough to wire it up, and then we can follow along with whatever wiring that we've ran. Those base plates are going to have at minimum a break away switch. In this case we've got an air line and a couple other things. more
4/20/2016 1:49:28 PM
Husky Shield Vehicle Paint Protectors Installation - 2012 Jeep Grand Cherokee- Video
Today on 2012 Jeep Grand Cherokee, we'll be installing the Husky Shield Vehicle Paint Protectors for the hood and door edges, part number HL06411. We'll also be using part number HL07999 which is an installation kit for the Husky Shield Vehicle Paint Protectors and is not included. We want to begin by adding the contents of the solution into our 32 oz spray bottle provided in the kit. Once we have those mixed, we can shake and then spray the front edge of the hood with a mixed solution. Now, we'll grab our surface prep putty and scrub the entire front edge of our hood. Be sure to only use the surface prep putty when the surface is wet. If used on a dry surface, the putty will be sticky and not perform as intended. more
8/20/2014 9:38:42 AM
Trailer Brake Controller Installation - 2012 Jeep Grand Cherokee- Video
Rate your transcript OrderClientKevin BrossRef #20497Order #TC0891082758 Today on our 2012 Jeep Grand Cherokee, we'll be installing our Tekonsha Prodigy P3 brake controller, part number 90195 with a direct fit wiring harness to connect directly to the manufacturer's brake controller port, part number 3045-P. Now, to begin the install of our new brake controller, on the driver side above the gas and brake pedal is a carpeted paneling that will need to be removed. To remove it, there are two push pin fasteners that will pry out that will release the carpeting, swing pull it out and set it aside for installation later. Next, above the emergency brake pedal, the white box is a grey plug. Grey plug will match the grey connector on the end of our new brake controller pigtail. We'll go ahead and put our grey plug on the pigtail into the grey socket on the manufacturer side. Now, once we push the connector into position and it locks in place, we'll go ahead and start the routing wires and securing it up underneath the dash. more
8/13/2014 12:50:06 PM
Convert-A-Ball Ball Mount Adapter Review - 2012 Jeep Grand Cherokee- Video
Today, on our 2012 Jeep Grand Cherokee, we'll be test fitting the Convert-A-Ball Ball Mount Adapter for Convert-A-Ball Cushioned Weight Distribution Shank, Part Number BA-1.Now, this is a great accessory if you purchased a Convert-A-Ball Weight Distribution Shank, Part Number AMAC1 for example. This can turn your weight distribution shank into a ball mount platform in two easy steps by placing the ball mount platform up against the rise or drop of the weight distribution shank and securing it with a pin and clip.You can use this ball mount platform when your weight distribution shank is in a rise or a drop to best fit your trailer configuration. That completes today's test fit for the Convert-A-Ball Ball Mount Adapter for Convert-A-Ball Cushioned Weight Distribution Shank, Part Number BA-1 on our 2012 Jeep Grand Cherokee. more
5/24/2013 11:19:32 AM
Convert-A-Ball Cushioned Weight Distribution Shank Review - 2012 Jeep Grand Cherokee- Video
Today, on a 2012 Jeep Grand Cherokee, we'll be test fitting the Convert-A-Ball Cushioned Weight Distribution Shank for Two-Inch Hitches, Part Number AMAC1.Before we begin our test fit, we will first need to obtain the hitch height of our vehicle. The hitch height is the measurement from the ground to the inside top of the receiver tube. We got a measurement of 14-1/2 inches.Keep in mind that this measurement will vary due to hitch style, tire size or any other aftermarket accessory.We'll now begin our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch, lining up the pinholes and securing it with the pin and clip.You can also flip the ball mount over into the rise position to give you some additional height.This ball mount can be used with a pintle hook combo with balls, which is sold separately; a ball mount adapter, which is also sold separately; and a Clevis Pin Adapter. You can choose the best accessory to fit your trailer configuration.That completes today's test fit for the Convert-A-Ball Cushioned Weight Distribution Shank for Two-Inch Hitches, Part Number AMAC1 on our 2012 Jeep Grand Cherokee. more
5/24/2013 11:05:04 AM
