Trailer Brake Controller Installation - 2003 Ford F-350- Video
Today in our 2003 Ford F250 superduty we're going to show you how to install the Tekonsha Primus IQ proportional trailer brake controller. This operates on of the 3 axials and part number is TK90160 we're also going to be using the pig tail, part number 3035-P for our factory Ford connection. Here's what our Primus IQ is going to look like once we get it installed. As you can see, nice easy to operate, easy to use style brake controller. We've got our manual override. It's right here. This is going to allow us to manually apply power to our brake in those emergency situations where maybe our trailer starts to get a little out of wack. more
6/5/2015 9:51:58 AM
Trailer Brake Controller Installation - 2003 Ford F-250 Super Duty- Video
Today on this 2003 Ford F250 Super Cab, we're going to install part number 90195. This is a Tekonsha Prodigy P3 Trailer Brake Controller. First, we'll go ahead and install our brake controller in the location on the truck. We're going to use this location right here. Our truck already had our brake controller previously installed here, so we're just going to reuse the existing holes. This is our bracket that comes with the P3 brake controller. more
9/5/2014 10:17:08 AM
Superwinch Front Mount Electric Winch Wiring Installation - 2003 Ford F-250- Video
Today on our 2003 Ford F-250 we'll be installing the Superwinch Front Vehicle Electric Winch Wiring Harness, Part Number SW2007. In today's video we'll be using the Superwinch Talon 12.5-I, Part Number SW1612210. Now we'll begin here on the winch. We're going to need to remove the cover that covers up the center solenoid section. We'll need to remove these 4 allen head bolts right here up underneath the cover. Once these are done we'll need to remove 2 more allen head bolts here on the end as well as 5 phillips head screws up underneath that will allow us to remove the cover and gain access to the bolt that holds the red wire, or the positive wire, on the solenoid side. We'll be removing the red wire which is the positive wire. more
1/20/2014 12:00:57 PM
Superwinch Electric Winch Wiring Kit Installation - 2003 Ford F-250- Video
Today on our 2003 Ford F-250, we will be installing the Superwinch Trailer and Vehicle Electric Winch Wiring Kit for up to 16,500 pound winches, part number, SW2008. In today's video, we'll be using the Superwinch Talon 12.5i, part number, SW1612210. We're going to need to remove the positive and the negative wire off of the winch itself and replace it with a short leads that come with the kit. Now, it's a good idea on your quick disconnect plug to go ahead and mark the ends of the wires that way you don't accidentally mix them up. Put a positive for the positive side as well as a dash for the negative side.Now, depending on your winch, the removal of the cover to get the positive side off might be a little bit different than hours. But for ours we'll need to remove these 4 Allen head bolts right here up underneath the cover. more
1/8/2014 10:35:44 AM
Curt Trailer Hitch Electric Winch Mount Plate Installation - 2003 Ford F-250- Video
Speaker: Today, on our 2003 Ford F-250, well be installing the Curt Trailer Hitch, electric winch mount plate part number C31010. In conjunction with the winch mount plate, well also be installing the Curt Trailer Winch mount handles part number C31005. The winch mount plate accommodates many different sizes as well as styles of electric winches. For todays purposes, well be installing the Superwinch Talon 12.5i winch. This is part number SW1612210. To begin with, were going to go ahead and put the winch mount plate into the rear receiver on this vehicle. Well then go ahead and put the pin and clip in place. more
1/7/2014 3:00:31 PM
Edge Backup Camera for Color Touch Screen Monitors Installation - 2003 Ford F-250- Video
Today on our 2003 Ford F250 well be installing the Edge Accessories backup camera for Edge color touch screens, part number EP98201. To begin our installation well remove the license plate frame containing the camera from the packaging, and after removing our license plate from our truck, here, well line up the bracket on the bumper where the license plate would bolt up. Youll notice that the camera has a wire that comes out of the frame here on the top. Our truck doesnt have a place where we can pass the wire through, so were going to go ahead and drill a hole. Youll notice that the wire has a rubber grommet on it already, so well use that grommet as a guide for the hole it will drill. We may need to open the hole up a little bit in order to get the grommet in. more
3/7/2013 3:22:47 AM
Bestop PowerBoard Motorized Running Boards Installation - 2003 Ford F-350- Video
Today on our 2003 Ford F350 well be installing the Beststop Powerboard motorized running boards with LED lights, part number B7510415. First well need to attach the motor linkage and idler linkage for our running board. To do this well first take the U nut, insert it into the inner rocker panel of the truck. Starting with the rear motor linkage well then use the new 8 mm bolt and flat washer and thread them into the U nut. Now well go ahead and take the motor linkage and slide it into position with the two bolts that we just installed. Next well take the two socket cap screws and 10 mm washers, thread them through the rocker panel and into the threaded portion of the motor linkage. more
11/1/2012 2:54:42 PM
Snap-Loc E-Track Tie-Down Anchor Installation - 2003 Ford F-250- Video
On this 2003 Ford F250, we're going to be installing the snap lock tie downs part # SLB25. To install this tie downs, we'll also use the hardware kit part # SLHZ. The first thing we need to do is position our snap locks on the bed of our truck. We'll take a paint marker and use it to mark our drill holes. Once we have our snap locks marked out, we'll go ahead and take a drill and drill out our holes. We also want to make sure that on the underside of the bed, we're not going to drill under anything like fuel lines or electrical systems. more
6/6/2012 6:52:37 AM
Pilot Automotive Navigator Off Road Light Installation - 2003 Ford F-250- Video
All right. Today on this 2003 Ford F-250, we're going to install part number NV-802C. Now, well actually be installing four of these on this vehicle. Well also be using the wiring kit, part number A-720. We're going to start off by installing the switch base onto a removable panel, that's below the steering column. Now, to transfer the pattern from our switch onto the backside of the panel. more
6/4/2012 4:13:30 PM
Trailer Brake Controller Installation - 2003 Ford F250- Video
Just to give you a reference point, this is the top, right here of the gas pedal, so basically its across up on this pillar here. While were here well plug in our brake controller adapter and that will be part # 3035-P. Now we can plug the other end of this into our brake controller after we install the mounting bracket. Next well mark our bracket for positioning, well just hold it up here on this bottom edge where its nice and flat. In this corner right here, well just make a small dot for reference and then well put our first screw there. Afterwards well put our brake controller inside and eyeball it to make sure we get it straight. When we have positioned the way we want it, we ll make our secondary screw install here. Okay at this point we can simply install our adapter cable in then well just mount right here. We have the brake controller installed now, the last thing we do is take the wires and zip tie them into a safe position and all we have to do is test. more
7/22/2008 9:21:09 PM
