B and W Gooseneck Trailer Hitch Installation - 2014 Ram 2500- Video
Hello, everybody. Clayton here at etrailer.com. Here at etrailer.com, we install, test, and review a lot of different products to help you, as a customer, make a more educated decision or purchase. Today we're gonna be working on a 2014 Ram 2500. We're gonna be taking a look at and I'll be walking through how to install B and W's turnover ball Gooseneck hitch. There are gonna be a couple benefits to using a Gooseneck versus a fifth wheel or a bumper pull. more
2/22/2021 2:54:21 PM
Best 2014 Ram 2500 Gooseneck Options- Video
Speaker 1: Today we're going to be looking at the best gooseneck options for our 2014 Ram 2500.While all of these will work with your Ram 2500 to allow you to haul a gooseneck trailer, there are some key differences that'll set them apart. The biggest difference is going to be their towing capacities. Both our B&W and our Curt are going to have a max towing limit of 30,000 pounds and a max vertical load limit of 7,500 pounds, while our Draw-Tite's going to be a little bit less with a maximum towing capacity of 20,000 pounds and a maximum vertical load limit of 5,000 pounds. It is always recommended to check your vehicle owner's manual to make sure it's not going to exceed any of its towing or load limit capacities.Now, what's really nice about the way all of these goosenecks install on our Ram 2500 is that there's no additional rail kit required. Most other vehicles require this additional rail kit, whereas our Ram 2500 has an existing rail system already included in the vehicle where these will just bolt right up to it using the hardware provided. Now, you will still need to drill your holes for your safety chains and ball, but there'll be no frame drilling which saves a lot of time. more
8/6/2018 1:32:13 PM
Superwinch 4-Circuit Breaker Installation - 2014 Ram 2500- Video
Today on our 2014 RAM Pickup Truck 2500 series we're going to be installing a super wench replacement 4 circuit breaker with bracket, part number SW90-22147, on a vehicle that has a super wench Talon series off road wench part number Sw1612210. We'll first begin here by raising up the hood. Now over here on the driver side battery, you can see here, this is where they already have the wench wiring connected to the positive side of the battery. So, we'll need to first disconnect that, and then we'll add our new circuit breaker inline. Go ahead and disconnect that for now. Go ahead and put this back on for now. Here's the circuit breaker that we're going to be installing today. more
9/5/2014 2:28:02 PM
Superwinch Front Mount Electric Winch Wiring Installation - 2014 Ram 2500- Video
Today on our 2014 Ram Pickup, we'll be installing the Super Winch front vehicle electric winch wiring harness, part number SW2007. We'll begin here on the winch. We're going to need to remove the cover that covers up the center cylinoid section. We'll need to remove these four Allen head bolts right here up underneath the cover. Once these are done, we'll need to remove two more Allen head bolts here on the end, as well as five Phillips head screws up underneath. That will allow us to remove the cover and gain access to the bolt that holds the red wire, or the positive wire on the cylinoid side. more
5/27/2014 5:35:10 AM
Convert-A-Ball Cushioned Weight Distribution Shank Review - 2014 Ram 2500- Video
Today on our 2014 Ram 2500, we'll be test fitting the Convert-A-Ball cushioned weight distribution shank for 2-inch hitches rated at 10,000 pounds, part number AMAC1. Now, our vehicle is equipped with a 2-1/2-inch hitch, so we'll be using the Blue Ox Hitch Reducer Sleeve from a 2-1/2-inch to a 2-inch hitch, part number BX88187. Before we begin our test fit, we'll need to get the hitch height of our pickup truck. With the adapter already inserted into the hitch, we have about a 24-inch hitch height. Keep in mind, this measurement may vary due to the tire size, hitch style, or after-market accessories. We'll start off our test fit in the drop position by sliding the shank of the weight distribution into the opening of our sleeve. We'll line up the 2 pin holes and then continue to slide the sleeve back into the hitch. We'll then insert the pin through the pin holes and then secure it with the clip on the other side. Now, there's a total of 7 holes on this weight distribution shank. more
3/27/2014 10:18:13 AM
