Hopkins Plug-In Simple Wiring Harness Installation - 2011 Ford Van- Video
Today on this 2011 Ford van, we're going to review and install the Hopkins Plug-In Simple Wiring Harness, part number HM11140665. This is what your wire harness looks like when it's installed on our van. This is a great component to add to your van if you don't have an existing four pole flap, because a lot of these vans do the port that's underneath the vehicle that's just not being used. Also, if the original equipment four pole has gotten corroded beyond use, you can also replace it with this part number as well.Let's cover what you get when you order this part number. First off, this is our wire harness right here that has a side that plugs into the factory port and your four pole flap on the other side. This whole wire harness is gonna be 70 inches long overall. more
12/12/2018 3:47:13 PM
Tekonsha T-One Vehicle Wiring Harness Installation - 2011 Ford Van- Video
Speaker 1: Today on our 2011 Ford van, we're going to review and install the T1 vehicle wiring harness from Tekonsha, part number 118260. This is what our four pole wire harness looks like once installed on our van. Just by itself, you could use a cap to help hold it in place. This is all one piece unit. It has traditional four pole flat on the end with built in cap to cover it, we're not using it. The whole assembly's about 50 inches long. more
12/5/2018 9:42:29 AM
Trailer Wiring Harness Installation - 2014 Ford Van- Video
Speaker 1: Today on our 2014 Ford Van we're gonna be taking a look at and showing you how to install the T-One vehicle wiring harness with a four-pole flat trailer connector, part number 118551.Here's what our wiring looks like when it's fully installed. Now it is gonna live on the outside of the vehicle and it's gonna provide us with a four-pole flat for our trailer giving us all the required lights to get down the road such as our turn signals, brake lights, and clearance lights.As far as the installation goes it's gonna be pretty straight forward. There's gonna be a few connections behind the taillights we're gonna have to make and then we're gonna have to run a line of wire up to the battery. Now that we've seen what it looks like when we're done let's show you how we get it installed.To begin our installation we're gonna need to remove our taillights and we're gonna have four fasteners holding them in place, I'm gonna be using a T15 torques bit to remove those. Once we have all the bolts removed we can grab the taillight and we gently pull it out and just push in on that tab, it should release the connector and we'll do the same thing for the other one. Now with this taillight removed we're gonna go ahead and do that on the other side too.We're gonna go ahead and grab our wiring harness and we're gonna start with a green wire on the passengers side. more
11/16/2017 11:38:00 AM
Trailer Wiring Harness Installation - 2009 Ford Van- Video
Today on our 2009 Ford E350 Econoline van, we're going to be taking a look at and installing the Curt T-connector Wiring Harness with Four Pole Flat Trailer Connector. Part number C56020. To test our wiring connection, we'll go ahead and take the ground side and connect that to the ground side of the plug and we'll test our brown wire, which would be our running lights, we'll get a constant signal. We'll test our left turn signal, which would be the yellow wire, we'll get that alternating signal, and the passenger side, or the right turn signal which will be that green wire. Now we'll go ahead and go brake lights, which should give us a constant signal on the green and the yellow. It looks like our wiring checks out, so we'll go ahead and plug it all back up and tuck it back away in the jack stand area. Now that we've seen how the wiring works, let's go ahead and see how it's installed. We'll remove both the driver and passenger side by removing the four T15 torx bit screws located here to secure the tail lights. more
12/14/2015 3:05:46 PM
Trailer Wiring Harness Installation - 2011 Ford Van- Video
Today, on this 2011 Ford Van E-350, we're going to show you Curt T-Connector Vehicle Wiring Harness with a 4-Pole Flat Trailer Connector. Part number C56020. With this part number, this is what you get. A wire harness here, this T-connector goes over to the passenger's side with the green wire, driver's with this yellow wire. We've got plenty of length of wire that comes up to the 4-pole flat. The kit also comes with zip ties to help secure the wires. more
8/8/2015 11:46:23 AM
Trailer Wiring Harness Installation - 2006 Ford Van 18252- Video
Today on our 2006 Ford van we're going to install part number 18252. This is a four pull hard wiring kit with circuit tester. First thing that you do is get our van ready. We need to take off the two tail lights. Starting on the drivers side here, we'll go ahead and remove the bolts. We're using a T 15 torque to take these out. The screws loosened, we'll go ahead and take out the remaining two. We'll just go ahead and leave our drivers side alone fore now. more
12/16/2014 12:12:13 PM
Trailer Wiring Harness Installation - 2004 Ford Van- Video
Today on our 2004 Ford Van, we'll be installing the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C56020. Let's go ahead and show you how to use your new 4-pole connector. We'll simply take the 4-pole connector out of the access slot next to the spare tire tools and run it out and over the threshold. Be careful to stay away from any latches, and simply close the rear cargo door on the wire. Then once were finished using our 4-pole connector with our accessory, well simply roll it up and store it in the spare tire tool compartment. By storing it inside, it will help protect it from the outside elements, providing more longevity for your new 4-pole harness.Now, lets go ahead and show you how to install it. more
12/6/2014 9:44:39 AM
Trailer Wiring Harness Installation - 2012 Ford Van- Video
Today on this 2012 Ford van E250 we're going to install part number 118260 from Tow Ready. This is the OEM replacement harness. Now our van does not have a harness already installed from the manufacturer but we we're able to find the port right here. Just remove it from the top rail. I already have it loosened up so I have to pry it off. I'll take the cap off, push down on this tab right here. more
11/14/2014 6:17:42 PM
Towready Taillight Converter Wiring Harness Installation - 1999 Ford Van- Video
Today on our 1999 Ford E450 van, we'll be installing the tow-ready, upgraded, circuit protected tail light converter, with 4-pull end, part number 119178. We're going to first need to take our test light here, and find out which wire does which function. Go ahead and ground our test light. Then we'll have someone turn on the running lights. We'll be tying them with this brown wire right here, with the white stripe on it. Go ahead and set up for our left or driver side blinker. more
5/6/2014 2:37:43 PM
Trailer Wiring Harness Installation - 2013 Ford Van C56020- Video
All right. Today in our 2013 Ford van, we're going to install part number C56020 from Curt. This is the Curt T-connector vehicle wiring harness. To start off our install, we're going to have to remove the tail lights. There are four screws in each tail lights that we have to remove. We'll do this on both sides. more
1/8/2014 4:09:40 AM
Trailer Wiring Harness Installation - 2006 Ford Van C56020- Video
Today on our 2006 Ford Van well be installing the Curt T-Connector Vehicle Wiring Harness with a 4-pole flat connector part number C56020. To begin our installation well first go ahead and remove both taillights. Each taillight is secured with four screws. Well go ahead and remove the screws and then pop the taillights out of their position. Well go ahead and let them hang there and well come back to that in a minute.Now with both taillights removed well go ahead and open up the rear cargo doors. Here well need to remove the rear threshold. more
5/21/2013 10:46:08 AM
Trailer Wiring Harness Installation - 2006 Ford E-350 Van- Video
Today on this 2006 Ford E350 van were going to install part number C56020 from Curt. The first thing we need to do is go ahead and remove the two taillights. Then well disconnect the taillights from the wire harnesses. Now well go ahead and get inside the van. Well open up the doors and remove the panel for the jack storage compartment. Next well remove the threshold. more
11/1/2012 3:08:04 PM
Trailer Wiring Harness Installation- 1994 Ford Van- Video
Today on this 1994 Ford Full Size Van, Club Wagon, we are going to install part number 118343 from Tow Ready. This T-1 connector connects behind both tail lights. What we are going to do is first remove the tail lights. We are going to let this sit just like this and go over to the other side and do the same thing. :21 more
2/23/2010 12:14:43 PM
Filter Videos
Filter Videos
