Summer Starts Here - Save up to 70%
Draw-Tite Max-Frame Trailer Hitch Installation - 2017 Buick Envision- Video
Speaker 1: Today on this 2017 Buick Envision we will be having a look at, and showing you how to install the Draw-Tite Class III trailer hitch receiver, part number 76080. Here's what the hitch looks like installed without our bumper cover back on. This is a really quick and easy installation. It doesn't' take much time at all even though you have to remove the entire fascia in order to get the bumper and the hitch into place. It attaches using factory studs that are already on the vehicle. There is no drilling, no cutting, no welding, no modification required at all. more
10/4/2017 11:48:41 AM
Trailer Hitch Installation - 2017 Buick Encore - Draw-Tite- Video
Speaker 1: Today in our 2017 Buick Encore, we're going to take a look at and also show you how to install the draw tite custom fit class two trailer hitch receiver; offering the inch and a quarter by inch and a quarter receiver tube opening. It's part number is 36554.Here's what our hitch is going to look like installed on the Encore. You can see we're going to have the smaller, round cross tube. It's just about all the way across the vehicle with the exception of here at the exhaust. It stops just a little bit short. Now, the center of the hitch is the receiver tube open itself. more
8/15/2017 8:42:06 AM
Trailer Hitch Installation - 2014 Buick Encore - Draw-Tite- Video
Today on our 2014 Buick Encore, we're going to be taking a look at and installing the Custom Fit Class 2 Draw Tite Trailer Hitch Receiver. Part number 36554. This is what our hitch looks like when it's fully installed. As you can see, our cross-tubes here are rounded and kind of have an angle to them. So follow the line to the back of the vehicle here. This is going to be a class two one and a quarter inch hitch. Here we have a plate style safety chain hookup to fit a wide variety of different chains. We have a half inch hitch pin hole to accept a variety of different hitch pins. more
5/15/2017 11:57:09 AM
Trailer Hitch Installation - 2015 Buick Encore - Draw-Tite- Video
Today on our 2015 Buick Encore, we're going to be taking a look at and installing the Draw-Tite Trailer Hitch Receiver class II, part number 36554. This is what your hitch is going to look like once it's installed. As you can see, it fits up very nice around the bottom of the bumper. It's an inch and a quarter class II hitch. It's got 300 lbs of tongue weight which is the downward force and 3,500 lbs of towing capacity, which is the amount your car is going to pull. You want to check with your manufacturer to make sure your vehicle's able to pull those weights. It's a round, tubular design that's completely welded. It's got a nice flat, large diameter safety chain loops. more
3/14/2016 1:41:21 PM
Trailer Hitch Installation - 2015 Buick Encore - Hidden Hitch- Video
Today on our 2015 Buick Encore, we're going to be taking a look at and installing the hidden hitch trailer hitch receiver with draw bar, class 2. Part number 90244. This is what you're hitch is going to look like once it's installed. As you can see, it fits up very nice around the bottom of the bumper, it's an inch and 1/4 class 2 hitch. It's got 300 pounds of tongue weight which is the downward force and 3500 pounds of towing capacity which is the amount your car is going to pull. You want to check with your manufacturer to make sure your vehicle is able to pull those weights. It's a round tubular design that's completely welded, it's got a nice flat, large diameter safety chain loops. more
3/11/2016 10:01:06 AM
Trailer Hitch Installation - 2015 Buick LaCrosse - Hidden Hitch- Video
Today on our 2015 Buick LaCrosse, we will be taking a look at and installing the hidden hitch, custom fit, class II trailer hitch receiver with draw bar, part number 90242. This is what our hitch will look like once it's installed. It's going to be nice and sleek, tucked up against the back side of the bumper. It's going to be that square tube, that's going to have a nice visual appearance and aesthetically pleasing from the back end of your vehicle. It's going to be fully welded on either of the two plates. Note that this does have a few plates that you will have to put together. You'll have one connected to the cross member in the back side and then the other plate here is going to be connected up top. more
9/30/2015 11:33:26 AM
Trailer Hitch Installation - 2015 Buick LaCrosse - Draw-Tite- Video
Today on our 2015 Buick LaCrosse, we're going to be taking a look at and installing the Draw-Tite custom fit Class II Trailer Hitch Receiver, part number 36538. This is what our hitch will look like once it's installed. It's going to be nice and sleek, tucked up against the back side of the bumper. It's going to be that square tube. That's going to have a nice visual appearance and aesthetically pleasing from the back end of your vehicle. It's going to be fully welded on either of the two plates. Not that this does have a few plates that you'll have to put together. You'll have one connected to the crossmember in the back side and then the other plate here is going to be connected up top, with the crossbeam connecting them both together. It's going to have four bolts located up here at the front, that's going to keep everything secured together. The receiver tube itself is going to be 1 1/4 inch x 1 1/4 inch with a 1/2 inch pin hole going all the way through. Capable of carrying up to 300 pounds, tongue weight, and carrying up to 3500 pounds, towing capacity. more
9/30/2015 11:32:57 AM
Trailer Hitch Installation - 2015 Buick Lacrosse - Curt- Video
Today on our 2015 Buick LaCrosse, we'll be reviewing and installing the Curt class 2 trailer hitch receiver, part number C12115. This is what you're hitch will look like once it's installed. It's going to be tucked up underneath the backside of the bumper, providing a nice sleek look, low profile from the back end of the vehicle. It's going to be black powder coated, for durability against the elements, and to prevent any kind of rust and corrosion. Up top you're going to have that inch and 1/4 by inch and 1/4 receiver tube, with a 1/2 inch pin hole going straight through. Chain tie downs on either side, you can see that you're going to have about enough room to get about two fingers through on each side. This hitch is capable of carrying 350 pounds of tongue weight, and 3,500 pounds of towing capacity. Remember that that towing capacity is your trailer, and everything in it combined. more
9/24/2015 11:52:53 AM
Trailer Hitch Installation - 2007 Buick Rendezvous - Curt- Video
Today on this 2007 Buick Rendezvous, we're going to show you Curt Trailer Hitch Receiver class III, with a 2-inch opening, part number 13469. All right. This is what the hitch looks like when it's installed on our Rendezvous. As you could see, it actually sits almost all the way underneath the bumper due to the vehicle's construction. even though it does sit pretty far back, it is a bit visible. Okay. Now, it does have a reinforced collar around the front edge of the receiver, makes it look nice. more
6/30/2015 2:06:27 PM
Trailer Hitch Installation - 2008 Buick Enclave - Curt- Video
Today on our 2008 Buick Enclave, we will be installing and taking a look at the Kerr Trailer Hitch Receiver Class 3 with a 2 Inch Opening, Part Number 13424. Here is what our Kerr Hitch looks like installed on our Buick Enclave. As you can see, it tucks nicely here behind our fascia. You do have to remove the trim piece right here to allow it to fit and unfortunately, it can not be re-installed. But it still gives it a nice look here with the square tube that goes across. All the hardware is hidden. Up underneath, it is a nice black powder coat finish so it is going to resist rust and corrosion. more
5/20/2015 4:14:36 PM
Trailer Hitch Installation - 2015 Buick Enclave - Draw-Tite- Video
Today we're going to be taking a look at then installing the Draw-Tite Max-Frame custom fit trailer hitch receiver. This is a class III 2-inch hitch. Part number is 75528. This going on our 2015 Buick Enclave. Here's what the hitch is going to look like once we've got it installed into the vehicle. That's right, we're going to be able to put our cover back on. We're not going to have this blank opening here with just a hitch sticking out where we can see it as we go. Just turn in the two set screws down here, kind of pulling down on that. more
2/20/2015 9:53:53 AM
Trailer Hitch Installation - 2015 Buick Enclave - Curt- Video
Today we're going to be taking a look at you installing our Curt Custom Fit Trailer Hitch Receiver. This a class 3, 2 inch Part Number is 13424. This is going on our 2015 Buick Enclave. Now, this is what you're hitch is going to look like once it's installed on your vehicle. As you can see cover goes back on nicely. If you want to put it on when you're not using your hitch you can, it's not going to be an issue. Keep the back of your car looking nice but still have all your tow power conveniently located underneath. You see our hitch tucks up fully under the bumper of the vehicle all the way across. more
2/18/2015 1:30:28 PM
Trailer Hitch Installation - 2009 Buick LaCrosse - Draw-Tite- Video
Today on our 2009 Buick LaCrosse, we'll be installing the Draw-Tite Hitch, part number 36374. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple measurements to assisted you with selecting accessories for your new hitch such as a ball mount, bike rack or cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is 6 inches. From the top of the receiver tube opening to the ground is 12 inches. We'll now go ahead with the installation. Now to begin our install, we'll first go ahead and lower the exhaust on the passenger's side. more
1/23/2015 10:29:17 AM
Trailer Hitch Installation - 1997 Buick LeSabre - Hidden Hitch- Video
Today on our 1997 Buick LeSabre we'll be installing Hidden Hitch 1-1/4" receiver tube hitch, part number 90188. Here's what our hitch will look like once it's installed. Next we'll go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 7-1/4". From the top of the receiver opening to the ground is 12-1/2". This will assist you with selecting accessories such as a ball mount, bike rack, or cargo carrier. more
12/31/2014 4:18:39 PM
Trailer Hitch Installation - 1997 Buick LeSabre - Draw-Tite- Video
Today on our 1997 Buick LeSabre we'll be installing the Draw-Tite hitch, part number 36216. Here's what our hitch will look like once it's installed. Next we'll go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 7-1/4". From the top of the receiver opening to the ground is 12-1/2". This will assist you with selecting accessories such as a ball mount, bike rack, or cargo carrier. more
12/31/2014 4:16:19 PM
Trailer Hitch Installation - 2000 Buick Regal - Draw-Tite- Video
Today on our 2000 Buick Regal we'll be installing the Draw-Tite Sportframe Trailer Hitch Receiver, part number 24660. To begin our installation we'll go ahead and open the trunk and remove the spare tire from the vehicle. With the spare tire removed you'll notice that there are two rubber plugs. We'll go ahead and remove these two rubber plugs. We'll then go ahead and test fit the square block, making sure that the square holes in the block line up with the holes on our vehicle. Before installing this block we'll go ahead and use some black silicone, work around the holes with the silicone to make sure that they seal up tight after we install our block. more
12/19/2014 2:39:29 PM
Trailer Hitch Installation - 2009 Buick Lucerne - HIdden Hitch- Video
Today on our 2009 Buick Lucerne, we'll be installing the Hidden Hitch Trailer Hitch Receiver, part number 90140. Here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple of measurements in helping you choose some accessories for your hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is approximately 6 inches. From the top of the opening in the receiver to the ground is approximately 13 inches. Now let's go ahead and install our hitch. We're going to go ahead and first begin by putting a safety strap to support our exhaust so that we can go ahead and remove some rubber exhaust hangers. more
12/19/2014 11:34:12 AM
Trailer Hitch Installation - 2009 Buick Lucerne - Draw-Tite- Video
Today on our 2009 Buick Lucerne we'll be installing the Draw-Tite Trailer Hitch Receiver part number 36309. Here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch such as a ball mount, a bicycle mount or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is approximately 6". From the top of the opening in the receiver to the ground is approximately 13". Now let's go ahead and install our hitch. We're going to go ahead and first begin by putting a safety strap to support our exhaust so that we can go ahead and remove some rubber exhaust hangers. We'll go ahead and loosen this bolt here that holds the bracket that supports the exhaust. more
12/19/2014 11:31:03 AM
Trailer Hitch Installation - 2006 Buick Rendezvous - Hidden Hitch- Video
Today, on our 2006 Buick Rendezvous, we'll be installing the Hidden Hitch, part number 90158. Here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch, such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper, it's approximately 5-1/2 inches. From the top of the opening in the hitch to the ground is approximately 12-3/4 inches. Now, let's go ahead and install our hitch. To begin with, let's go ahead and point out the locations that we'll be using to mount our hitch. more
11/18/2014 4:17:34 AM
Trailer Hitch Installation - 2011 Buick Lacrosse - Curt- Video
Today on our 2011 Buick Lacrosse were going to be installing the Curt Trailer Hitch Receiver, part number C12115. Now heres what our hitch looks like installed on our vehicle. Now well go ahead and give you a couple measurements in helping you choose some accessories for your hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is approximately four inches. From the top of the opening in the receiver to the ground is approximately 10-1/2 inches. Now lets go ahead and install our hitch. First lets go ahead and point out our mounting locations that well be using to secure the hitch to the vehicle. To begin with well start here on the drivers side. more
11/17/2014 3:48:30 PM
Trailer Hitch Installation - 2013 Buick Encore - Hidden Hitch- Video
Today on our 2013 Buick Encore, we're going to be installing the Hidden Hitch Trailer Hitch Receiver, part number 90223. Now here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple measurement in helping you choose some accessories for your hitch such as a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is approximately 5 inches. From the top of the opening in the receiver to the ground is approximately 11-1/4 inches. Now, let's go ahead and install our hitch. We're going to first begin our installation by installing a safety strap underneath the exhaust. Next, we're going to need to remove two rubber isolators that support the exhaust. There's one over here on the driver side and one over here on the passenger side. more
11/7/2014 12:54:46 PM
Trailer Hitch Installation - 2013 Buick Encore - Draw-Tite 36527- Video
Today on our 2013 Buick Encore, we're going to be installing the Draw-Tite Trailer Hitch Receiver, part number 36527. Now here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple measurement in helping you choose some accessories for your hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is approximately 5 inches. From the top of the opening in the receiver to the ground is approximately 11-1/4 inches. Now, let's go ahead and install our hitch. We're going to first begin our installation by installing a safety strap underneath the exhaust. Next, we're going to need to remove two rubber isolators that support the exhaust. There's one over here on the driver side and one over here on the passenger side. more
11/7/2014 12:51:06 PM
Trailer Hitch Installation - 2005 Buick Rendezvous - Draw-Tite- Video
Today on our 2005 Buick Rendezvous, we're going to be installing the Draw-Tite trailer hitch receiver, part number 75430. Now here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple measurements in helping you choose some accessories for hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is approximately 6 1/2 inches. From the top of the opening in the receiver to the ground is approximately 12 3/4 inches. Now let's go ahead and install our hitch. Let's go ahead and begin here underneath the vehicle and we're going to point out our mounting locations that we'll be using. more
10/25/2014 12:01:57 PM
Trailer Hitch Installation - 2012 Buick Enclave - Draw-Tite- Video
Today on our 2012 Buick Enclave we'll be installing the Draw-Tite Hitch, part number 75528. Here's what our hitch will look like once it's installed. Next we'll go ahead and give you a couple measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin holes to the outer most edge of the bumper it's 4 and 3 quarter inches. From the top of the receiver tube opening to the ground is 18 and a quarter inches. This will assist your selecting accessories such as ball mount, bike rack or cargo carrier. Now we'll go ahead with the installation. To get our install we'll first need to remove the rear fascia door. more
10/17/2014 1:02:51 PM
Trailer Hitch Installation - 2011 Buick Enclave- Video
Today on our 2011 Buick Enclave, we'll be installing our Curt hitch, part number 13424. This is what our hitch will look like once it's installed. Next we'll give you a couple of measurements. This will assist your selecting accessories such as a ball mount, bike rack, or cargo carrier. From the center of hitch-pin hole to the outer most edge of the bumper is 5 inches. From the top of the receiver-tube opening to the ground is 18-3/4 inches. Now we'll go ahead with installation. To begin our install, we'll first need to remove the rear fascia door. more
10/14/2014 3:01:41 PM
Trailer Hitch Installation - 2008 Buick Enclave - Draw-Tite- Video
Today on this 2008 Buick Enclave we're going to install part number 75528 from Draw-Tite. This is what the hitch looks like once it's installed on the vehicle. Next, we'll give you some measurements to help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground will be about eighteen inches. From the center of the hitch pinhole to the edge of the bumper will be about four and a half inches. Now we'll go ahead and show you how the hitch is installed. First thing we need to do is go ahead and remove the fascia door. more
10/14/2014 2:59:34 PM
Trailer Hitch Installation - 2014 Buick Enclave - Draw-Tite- Video
Today on our 2014 Buick Enclave, we're going to be installing the Draw-Tite trailer hitch receiver, part number 75528. Now, before we begin the installation, let's go over the tools that we're going to need to do that. We need a safety strap, a large pry bar, little bit of spray lubricant, nylon tube brush, pair of tin snips, flat head screwdriver, 18 mm wrench preferably a ratcheting style box in order 00:00:34 to help things out, need an 18 mm socket, 3-1/4 inch socket, ratchet, and a torque wrench to secure everything down. Now, here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch such as a ball mount, a bicycle rack or cargo carrier. From the center of the hitch pin hole out to the outermost edge of the bumper is approximately 5 inches. From the top of the opening in the receiver to the ground is approximately 19 inches. Now, let's go ahead and install our hitch. Now, to begin our installation, we're going to first need to remove this lower trim panel here. more
9/24/2014 4:55:38 PM
Trailer Hitch Installation - 2014 Buick Enclave - Curt- Video
Today on our 2014 Buick Enclave, were going to be installing the Curt Trailer Hitch Receiver, part number 13424. Before we begin our installation today, lets go over the tools that well be using to install our hitch. Well be using a 3/4 inch socket and ratchet, 3/4 inch ratcheting style wrench will come in handy too, a large pry bar, a safety strap, a tube brush for cleaning out weld nuts, a little spray lubricant and of course our torque wrench to torque down the hardware. Heres what the hitch looks like installed on our vehicle. Now well go ahead and give you a couple measurements in helping you choose some accessories for your hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pinhole to the outer most edge of the bumper is approximately 5 inches. more
9/24/2014 4:52:33 PM
Trailer Hitch Installation - 2006 Buick Lucerne - Curt- Video
Today on this 2006 Buick Lucerne, were going to install part number C12044 in currant. All right, the first thing we need to do is go ahead and get our car ready. We need to lower the exhaust. Before we do that, well go ahead and use a strap to help hold our exhaust and support it while we undo the fasteners that are holding the exhaust in place. Well go ahead and remove the exhaust hanger bracket from the bottom of the frame rail. In this case, our vehicle was a dual exhaust. There is a bolt well have to remove for the hanger bracket, another one on each side. Now, well go towards the front of the exhaust a little bit, where weve got another set of hangers. more
7/31/2014 12:59:19 PM
Trailer Hitch Installation - 2013 Buick Enclave - Curt- Video
Today on our 2013 Buick Enclave, we'll be installing the Curt Trailer Hitch Receiver in a Class 3, with a 2-inch receiver opening. Part number 13424. Here's what the hitch looks like installed on our vehicle. Now I'll go ahead and give you a couple of measurements in helping you choose some accessoriesfor your hitch, such as a ballmount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outermost edges of the bumper is, approximately4 1/2 inches. From the top of the opening of the receiver to the ground isapproximately18 inches.Now, let's go ahead and install our hitch. We'll begin by removing the center plastic section on our rear lower bumper fascia. Todo this, there are two tabs, one on each side, that we'll need to turn. Then simply pull down on the center section, and it will release from the bumper cover. Now, we can go ahead and see the mounting locations of where we're putting our hitch job with. more
12/6/2013 2:45:01 PM
Trailer Hitch Installation - 2006 Buick Rendezvous - Draw-Tite- Video
Today in our 2006 Buick Rendezvous well be installing the Draw-Tite Max-Frame Trailer Hitch Receiver in a Class III with a two-inch opening on the receiver, part number 75138. Heres what our hitch looks like installed on our vehicle. We will go ahead and give you a couple of measurements in helping you choose some accessories for your hitch such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the outmost edge of the bumper is approximately 5 inches. From the top of the opening in the receiver to the ground is approximately 12 inches. Lets go ahead and install our hitch. Well start here underneath the rear bumper fascia at the rear of the vehicle. There are a total of five push-in retaining clips that well need to remove first. more
10/25/2013 1:04:07 PM
Trailer Hitch Installation - 2004 Buick Rendezvous - Draw-Tite- Video
All right, today on this 2004 Buick Rendezvous, were going to install part number 75430 from Draw-Tite. All right, this is what the hitch looks like when its installed on the vehicle. Next well give you some measurements thatll help out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down the ground will be about 13-1/4 inches. From the center of the hitch pinhole to the edge of the bumper will be about 5-1/2 inches. Now Ill go ahead and show you how the hitch is installed. Before we install the hardware, well show how it looks on the hitch. Youll see you have the bolt and blocks will be inside the frame and then go through the hitch and on the bottom of the hitch, youll have the conical tooth washers and nuts. more
1/28/2013 1:48:32 AM
Trailer Hitch Installation - 2003 Buick Rendezvous - Hidden Hitch- Video
Today on this 2003 Buick Rendezvous were going to install part number 90158 from Hidden Hitch. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground is going to be about 13 inches. From the center of the hitch pin hole to the edge of the bumper is going to be about five and three-eighths. Now well go ahead and show you how the hitch is installed. more
1/25/2013 9:14:04 AM
Trailer Hitch Installation - 2003 Buick Rendezvous - Draw-Tite- Video
Today on this 2003 Buick Rendezvous were going to install part number 36425 from Draw Tite. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground is going to be about 13 inches. From the center of the hitch pin hole to the edge of the bumper is going to be about five and three-eighths. Now well go ahead and show you how the hitch is installed. more
1/25/2013 9:13:54 AM
Trailer Hitch Installation - 2010 Buick Enclave - Curt- Video
Today on our 2010 Buick Enclave well be installing the Curt hitch, part number 13424. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is five and a quarter inches. From the top of the receiver tube to the ground is 18 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or cargo carrier.Now well go ahead with installation. more
11/5/2012 11:17:00 AM
Trailer Hitch Installation - 2001 Buick Park Avenue - Draw-Tite- Video
Today on our 2001 Buick Park Avenue, well be installing Draw-Tite hitch part number 36245. This is what your hitch will look like on the vehicle. Now, well give you a few measurements to help you when selecting accessories. From the top of the receiver tube to the ground is 11 inches and from the center of the hitch pinhole to the outermost part of the bumper is 7 inches. Now, well go ahead with our install. Well need to remove the exhaust hanger here on the passenger side. more
6/4/2012 10:36:41 AM
Trailer Hitch Installation - 2011 Buick LaCrosse - Hidden Hitch- Video
Today on this 2011 Buick Lacrosse were gonna install part number 90126 from Hidden Hitch. The model were working with today will be the CXL model. This is what the hitch looks like once its installed in the vehicle. Next well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground is going to be 12 inches and from the center of the hitch pinhole to the outside edge of the bumper, were looking at 7 inches. Now well go ahead and show you how the hitch is installed. more
4/12/2012 2:55:01 PM
Trailer Hitch Installation - 2011 Buick LaCrosse - Draw-Tite 36503- Video
Today on our 2011 Buick-lacrosse were going to install part number 36503 from Draw-Tite. The model were working with today will be the CXL model. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of our receiver opening down to the ground its going to be 12-1/4 inches and from the center of the inch pinhole to outside edge of the bumper were looking at 7-1/4 inches. Now Ill go ahead and show you how the hitch is installed. more
4/12/2012 2:54:39 PM
Trailer Hitch Installation - 2012 Buick Enclave - Curt- Video
Today on our 2012 Buick Enclave, we'll be installing part number 13424 from Curt. Here are a couple of measurements to help you when selecting accessories. From the top of the receiver tube to the ground is 18-3/4 and from the center of the hitch pinhole to the outermost point of the bumper is 4-1/4. Now well go ahead with our install. To begin our install, well need to remove the cover here at the rear bumper. To do that well just undo the clasps on either side. more
3/23/2012 2:57:39 AM
Trailer Hitch Installation - 2002 Buick Park Avenue- Video
Today on this 2002 Buick Park Avenue, were going to install part number 36245 from Draw Tite. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements that will help you out when selecting some accessories. From the top of the receiver opening down to the ground on this particular vehicle is going to be 12-1/4 inches, and from the center of your pin hitch hole to the outside edge of the bumper is going to be 7-1/4 inches. Now lets go ahead and show you how the hitch is installed on the car. Okay first step we need to do is go ahead and lower the exhaust underneath the vehicle, and unbolt the hanger. more
10/24/2011 2:17:03 PM
Trailer Hitch Installation - 2003 Buick Park Avenue- Video
Today on this 2003 Buick Park Avenue we are going to install part number 36245 from Draw-Tite. Next we will give you some measurements that will help you out when ing accessories, such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground, on this particular vehicle, is going to be 12-1/4 inches. And from the center of the hitch pin hole to the outside edge of the bumper is going to be 7 inches. Next we will go ahead and show you how the hitch gets installed. 0:25 more
7/20/2011 10:37:41 AM
Trailer Hitch Installation - 2006 Buick Lucerne- Video
Today on this 2006 Buick Lucerne, we are going to be installing Draw-Tite hitch part number 36309. And this installation will also apply to Hidden Hitch part number 90140. OK, we are underneath the vehicle and we are taking a look at the driver side frame rail. We want to go ahead and point out the mounting location for the trailer hitch. The first thing that I want to note is that we do have exhaust here, right in the way of the frame rail. And on this particular vehicle, we do have dual exhaust. So, it is the same on both the driver and passenger side. We do need to lower the exhaust down. In doing so, we want to go ahead and take and remove the bolt at the rear portion of the frame here. And that is going to lower down the exhaust bracket. We want to do that on both the driver and passenger sides for dual exhaust models. Before lowering the exhaust hangers though, I do want to go ahead and put a support strap across the main exhaust tube here, at the forward side of the vehicle. The reason is, once you remove the exhaust off of its hangers, it could put additional strain on the forward exhaust hangers and possibly allow it to fall and damage the exhaust. 0:55 more
8/4/2010 11:15:54 AM
Trailer Hitch Installation - 2004 Buick Rendezvous- Video
Today on this 2004 Buick Rendezvous we will be installing Draw-Tite hitch part number 36425. This installation will also apply for Hidden Hitch part number 90158. We are underneath the vehicle near the bumper, we are looking at the driver side frame rail. As you can see we have two large oblong holes at the end of the frame rail and we are going to be using both of those as attaching points for our trailer hitch. We will be placing carriage bolts and blocks up inside the frame and pulling it back down into position for both of those locations. That is going to be the same on the passenger side as well. If you notice further rearward we have this lip that is attaching the body to the bumper. We are going to be drilling four holes, two per side, to attach the trailer hitch to as well. What we want to do first is put the hardware into the frame, get the hitch up into position, and we will use the hitch as a template to drill those holes out. 00:47 more
3/29/2010 5:40:57 AM
Trailer Hitch Installation - 2002 Buick LeSabre- Video
Today we are going to be installing Draw-Tite hitch part number 36309 on a 2002 Buick LeSabre. This hitch application will also apply to the Hidden Hitch part number 90140. Okay, underneath the vehicle, we are going to go ahead and take a look at the frame rails and point out the mounting location for the trailer hitch. Looking at the passengers side frame rail, you can see we have got the exhaust here that is mounted to this bracket here at the end of the frame. We are going to need to lower that down. The weld nut that this bolt is attached to, which is holding our exhaust bracket on, is going to provide our rear-most attaching point for the trailer hitch. And that is going to be the same on both sides of the vehicle. Our more forward attaching point we are actually going to have to drill. So what we will do is put the hitch up in position with our rear-most attaching point, and then we will use the hitch as a template to drill the hole out on each side. more
8/5/2009 8:07:48 AM
Filter Videos
Filter Videos
