Summer Starts Here - Save up to 70%
Trailer Hitch Installation - 2008 Chrysler Town and Country - Draw-Tite- Video
Today on our 2008 Chrysler Town and Country we'll be installing the Draw Tite Hitch, part number 36455. This is what our hitch will look like once installed. Next we're going to give you a couple measurements to assist your selecting accessories for your new hitch such as a ball mount, bike rack or cargo carrier. From the center of the hitch hole to the outer most edge of the bumper is 7 inches. To the top of the receiver tube opening to the ground is 13 inches. Now we're go ahead with installation. To begin our install we'll first go ahead and identify our attachment points. We'll have a total of 4 attachment points, 2 on each side. more
9/11/2014 3:18:40 PM
Trailer Hitch Installation - 2012 Chrysler Town and Country - Hidden Hitch- Video
Today in our 2012 Chrysler Town and Country we will be installing Hidden Hitch 1 1/4 inch receiver tube hitch, part number 90169. This is what our hitch will look like once it is installed. Next I am going to give you a couple of measurements. This will assist your selecting accessories such as a ball mount, bike rack or cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is 6 1/4 inches. From the top of the receiver tube opening to the ground is 13 inches. more
6/13/2014 1:28:57 PM
Trailer Hitch Installation - 2012 Chrysler Town and Country - Draw-Tite- Video
Today on our 2012 Chrysler Town and Country, we'll be installing the Draw-Tite Hitch, part number 36455. This is what our hitch will look like once installed. Next I'll go ahead and give you a couple measurements, this will assist you with selecting accessories such as a ball mount, bike rack, or cargo carrier. From the center of the hitchpin hole to the outermost edge of the bumper is 6 and 1/4 inches. From the top of the receiver tube opening to the ground is 13 inches. Now I'll go ahead with the installation. Starting on the passenger side, we'll need to lower the exhaust. more
6/13/2014 1:28:48 PM
Trailer Hitch Installation - 2001 Chrysler Sebring - Draw-Tite- Video
Today on our 2001 Chrysler Sebring convertible well be installing the DrawTight Sportframe trailer hitch receiver in a class 1 with an inch and a quarter opening part #: 24711. Heres what our hitch looks like installed on our vehicle. Now well go ahead and give you a couple of measurements in helping you choose some accessories for your hitch such a bicycle rack or a cargo carrier. From the center of the hitch pinhole to the outermost edge of the bumper is approximately eight and a half inches. From the top of the opening of the receiver to the ground is approximately 12 and a quarter inches. Now lets go ahead and install our hitch. more
10/25/2013 9:23:53 AM
Trailer Hitch Installation - 2008 Chrysler Pacifica - Hidden Hitch- Video
Today on our 2008 Chrysler Pacifica we'll be installing hidden hitch, part number87432. This is what ourhitch will look like once installed. Next we'll go ahead andgive you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of thebumper is three and one quarter inches, from the top of the receiving tube to the ground is eleven and a half inches. This will assist your selecting accessories, such as a ball mount, bike rack, or cargo carrier. Now we'll go ahead with installation. We'll go ahead and point out the attachment points. more
10/23/2013 9:13:54 AM
Trailer Hitch Installation - 2008 Chrysler Pacifica - Curt- Video
Today on our 2008 Chrysler Pacifica well be installing the Curt two inch receiver hitch, part number 13529. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is three and three quarter inches. From the top of the receiver tube to the ground is 11 inches. This will assist you with selecting accessories such as a ball mount, bike rack or cargo carrier.Now well go ahead with installation. more
10/23/2013 9:09:54 AM
Trailer Hitch Installation - 2008 Chrysler Pacifica - Draw-Tite- Video
Today on our 2008 Chrysler Pacifica Im installing the Draw-Tite two-inch receiver tube hitch part number 75522. This is what our hitch will look like once its installed. Next is going to be a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3-1/4 inches. From the top of the receiver tube to the ground is 11-1/2 inches. This will assist your selecting accessories such a ball 00:00:25 mount, bike rack or cargo carrier.Now well go ahead with installation. more
10/23/2013 9:06:39 AM
Trailer Hitch Installation - 2014 Chrysler Town and Country - Hidden Hitch 87451- Video
Today in our 2014 Chrysler Town and Country, we'll be installing hidden-hitch part #87451. Next we're going to give you a couple of measurements to assist you selecting accessories for your new hitch. From the center of the hitchment hole to the outermost edge of the bumper is approximately 6 1/4 inches. From the top of the receiver tube opening to the ground is 13 1/4 inches. Now, go ahead with installation. First, to begin install, go ahead and point out the attachment points. To secure a hitch to the vehicle, there will be a total of five attachment points. These attachment points will be well nuts built into the frame by the manufacturer. We'll have three on the driver's side. Two on the passenger. To gain easier access to our attachment points, especially on the passenger side above the exhaust, we'll lower the exhaust by removing to two fasteners securing the rear hangers. One, just front of the rear muffler and one just behind the front muffler. With our exhaust lowered and out of the way, we'll go ahead and remove the manufacturer's hardware. However, we will hang onto it as we'll use it to secure the hitch to the vehicle. Now, with the exhaust down and out of the way, we'll install the air conditioning line protector to prevent any contact with the hitch. We're ready to put our hitch in place. Take the passenger side, feed it up over the exhaust. more
10/21/2013 4:14:23 AM
Trailer Hitch Installation - 2014 Chrysler Town and Country - Curt- Video
Kurt: Today in this 2014 Chrysler Town and Country, we're going to install part number 13364 from Curt. All right this is what the hitch looks like when installed on the van. Next I'll give you some measurements to help you out selecting some accessories, such as a ball mount, a bicycle rack, or a cargo carrier. From topper receiver opening down to the ground will be about 13 1/2 inches. From the center of a hitch pin hole, the edge of the bumper will be about 4 1/2 inches. Now Ill go ahead and show you how the hitch is installed. To start off our install we're going to need some room to install our hitch. more
10/16/2013 12:57:47 PM
Trailer Hitch Installation - 2007 Chrysler 300 - Curt- Video
Today on our 2007 Chrysler 300, we will be installing Curt Hitch, part number C12240. Before we begin our installation, here are a few measurements to help you on selecting accessories such as a bike rack or a cargo carrier. From the center of the hitch pin hole to the outer most part of the bumper is 7 inches. From the top of the receiver tube to the ground is 12 inches. Now lets go ahead with our install. Before we begin our installation, we will need to lower our exhaust. Well first put a safety strap underneath the vehicle to hold the exhaust while we undo the mounting location. On the two rear most isolators, we can go ahead and undo the bolts holding the isolators to the vehicle. more
3/7/2013 3:23:59 AM
Trailer Hitch Installation - 2005 Chrysler 300 - Curt- Video
Today on our 2005 Chrysler 300, we'll be installing the CURT hitch, part number 13465. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch-pin hole to the outermost edge of the bumper is 6 3/4 inches. From the top of the receiver tube opening to the ground will be 10 1/4 inches. This will assist you selecting accessories, such as a drawbar, a bike rack, or cargo carrier. more
2/15/2013 2:18:29 PM
Trailer Hitch Installation - 2013 Chrysler Town and Country - Hidden Hitch- Video
Today on this 2013 Chrysler Town and Country were going to install part number 87451 from Hidden Hitch. This is what the hitch looks like once its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 13 inches. From the center of the hitch pin hole to the edge of the bumper will be about six and a quarter inches. Now well go ahead and show you how the hitch is installed. more
2/8/2013 3:45:27 PM
Trailer Hitch Installation - 2013 Chrysler Town and Country - Draw-Tite 75579- Video
Today on this 2013 Chrysler Town and Country, were going to install part number 75579 from Draw Tite. All right this is what the hitch looks like once its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground will be about 13-1/4 From the center of the hitch pin hole to the edge of the bumper will be about 6-1/4.Now well go ahead and show you how the hitch is installed. The first step is to go ahead and lower the exhaust. Right behind the muffler is a hanger well unbolt and one above the axial that well unbolt as well. more
2/8/2013 2:52:22 PM
Trailer Hitch Installation - 2013 Chrysler Town and Country - Draw-Tite 36455- Video
Today on this 2013 Chrysler Town and Country, were going to install part number 36455 from Draw Tite. This is what the hitch looks like once its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 13-1/4 and from the center of the hitch pin hole to the outside edge of the bumper will be about 6-3/4. Now well go ahead and show you how the hitch is installed. First thing we need to do before we do our install is to go ahead and lower the exhaust out of the way. more
2/8/2013 2:52:17 PM
Trailer Hitch Installation - 2007 Chrysler Town and Country - Curt- Video
Today on our 2007 Chrysler Town and Country, well be installing Curt Hitch part number 13389. Now before we begin our installation heres what your hitch will look like on the vehicle. Well go ahead and give you a few measurements to assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier. From the top of the receiver tube to the ground measures 12 and from the center of the hitch pin hole to the outer most part of the bumper measures four inches. With that well go ahead and start our installation. To begin our installation, well need to locate the attachment points on the vehicle frame. more
2/4/2013 10:27:19 AM
Trailer Hitch Installation - 2007 Chrysler Town and Country - Draw-Tite 75305- Video
Today on our 2007 Chrysler Town and Country, well be installing Draw-Tite Hitch, part number 75305. Now before we begin our install, heres what your hitch will look like on the vehicle. At this point well go ahead and give you a few measurements to help assist you when selecting accessories such as a drawbar, a bike rack or a cargo carrier. From the top of the receiver tube to the ground measures 12 inches and from the center of the 5/8 inch hitch pinhole to the outermost part of the bumper measures 2 inches. Now lets go ahead with our install. Now to being our installing, well need to locate the three attachment points on either side of the frame. more
2/1/2013 1:28:32 PM
Trailer Hitch Installation - 2002 Chrysler Town and Country - Draw-Tite- Video
Today on this 2002 Chrysler Town & Country we're going to install part number 36296 from Draw-Tite. This is what he hitch looks like when it's installed on a vehicle. Next we'll give you some measurements that will help you out in selecting some accessories, such as a cargo carrier or a bicycle rack. From top to receiver opening down to the ground will be about 13 and a quarter inches. From the center of the hitch pin hole to the edge of the bumper will be about four and three-quarter inches. Now I'll go ahead and show you how the hitch in installed. First thing we need to do is get underneath the vehicle and we need to remove the front bumper bolts. You'll see two bolts at the bottom of the frame. more
11/21/2012 9:18:56 AM
Trailer Hitch Installation - 2002 Chrysler Town and Country - Draw-Tite 24702- Video
Today on this 2002 Chrysler Town and Country were going to install part number 24702 from Draw Tite. This is what the hitch looks like once its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories such as a cargo carrier or a bicycle rack. From the top of the receiver opening down to the ground will be 12 inches. From the center of the hitch pin hole to the edge of the bumper will about four inches. Now Ill go ahead and show you how the hitch is installed. more
11/21/2012 9:18:49 AM
Trailer Hitch Installation - 2013 Chrysler 200 - Draw-Tite- Video
Today on our 2013 Chrysler 200, we'll be installing the Draw-Tite Hitch, part #24871. Now, well go and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 7-1/4 inches. From the top of the receiver tube opening to the ground is 10-1/2 inches. This will assist you in selecting accessories such as a bike rack or a cargo carrier. Now, lets go ahead with installation. more
11/19/2012 10:45:08 AM
Trailer Hitch Installation - 2010 Chrysler Town and Country - Draw-Tite- Video
Today on our 2010 Chrysler Town and Country were going to install part number 36455 from Draw Tite. This is what the hitch looks like when its installed on the van. Next well give you some measurements that will help you out in selecting some accessories, such as a bike rack or a cargo carrier. From the top of the receiver opening down tot eh ground will be about 12 inches. From the center of the hitch pin hole to the edge of the bumper will be about six and three-quarter inches. Now well go ahead and show you how the hitch is installed. more
11/19/2012 10:45:00 AM
Trailer Hitch Installation - 2013 Chrysler Town and Country - Curt 13364- Video
Today on our 2013 Chrysler Town and Country well be installing Curt hitch part number 13364. Well go ahead and give you a few measurements to help you with selecting accessories such as a draw bar, bike rack, or a cargo carrier. From the center of the hitch pin hole to the outer most part of the bumper is four inches. From the top of the receiver tube to the ground is 12 and a quarter inches. Now to begin our installation well need to lower the exhaust. Well remove the bolts holding the exhaust and muffler hangers. more
10/26/2012 11:47:10 AM
Trailer Hitch Installation - 2009 Chrysler Town and Country - Curt- Video
Today on our 2009 Chrysler Town and Country, well be installing the curt hitch part number 13364. First, well go ahead and low the exhaust to give us more access here on the passenger side to the frame rail. To lower the exhaust well remove the two fasteners. One just forward of the rear axle and one just behind it. In the passengers side, well be removing the two rear fasteners that go into the weld nuts or bumper brace of the vehicle. On the drivers side, well remove the three rear fasteners. more
10/4/2012 7:48:16 AM
Trailer Hitch Installation - 2011 Chrysler Town and Country - Hidden Hitch- Video
Today on this 2011 Chrysler Town and Country, were going to install part number 87451 from Hidden Hitch. This is what the hitch looks like once installed on the van. Next, well give you some measurements to help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the edge of the bumper its going to be six and a quarter inches. From the top of the receiver opening down to the ground will be 12 and half inches. Now Ill go ahead and show you how the hitch is installed. more
9/11/2012 9:09:06 AM
Trailer Hitch Installation - 2011 Chrysler Town and Country - Curt- Video
Today on this 2011 Chrysler Town and Country, were going to install part number 13364 from Curt. This is what the hitch looks like once installed on the van. Next, well give you some measurements to help you out in selecting some accessories such as the ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin opening to the edge of the bumper is going to be four and a quarter inches. From the top of the receiver opening down to the ground will be 12 and half inches. Now Ill go ahead and show you how the hitch is installed. more
9/11/2012 9:08:26 AM
Trailer Hitch Installation - 2007 Chrysler Pacifica - Curt- Video
Today on this 2007 Chrysler Pacifica were going to install part number 13529 from Curt. This is what the hitch looks like when its installed on a vehicle. Next well go ahead and give you some measurements to help you in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground is going to be 11 inches. From the center of the hitch pin hole to the edge of the bumper is going to be three and a quarter inches. Now Ill go ahead and show you how the hitch is installed. more
9/6/2012 9:56:34 AM
Trailer Hitch Installation - 2011 Chrysler Town and Country - Hidden Hitch 90169- Video
Today on our 2011 Chrysler Town and Country well be installing Hidden Hitch part number 90169. To being our installation, well need to lower the exhaust by removing the bolt which attaches the rearmost hanger to the passenger side frame rail. Well also going to go ahead and remove the bolt holding the hanger just forward of the rear axle. This is just so we can drop the exhaust a little farther to be able to see. Next, here on the driver side, were going to remove the existing bolts from the frame rails. Now these are the locations that well be mounting the hitch so well need to retain the fasteners as well be reusing them to mount the hitch. more
7/10/2012 10:55:09 AM
Trailer Hitch Installation - 2011 Chrysler Town and Country - Draw-Tite 36455- Video
Today on our 2011 Chrysler Town and Country well be installing Draw-Tite Hitch part number 36455. To being our installation, well need to lower the exhaust by removing the bolt which attaches the rearmost hanger to the passenger side frame rail. Well also going to go ahead and remove the bolt holding the hanger just forward of the rear axle. This is just so we can drop the exhaust a little farther to be able to see. Next, here on the driver side, were going to remove the existing bolts from the frame rails. Now these are the locations that well be mounting the hitch so well need to retain the fasteners as well be reusing them to mount the hitch. more
7/10/2012 10:54:40 AM
Trailer Hitch Installation - 2006 Chrysler 300 - Curt- Video
Today on our 2006 Chrysler 300, well be installing the Curt Hitch, part number 13465. This is what our hitch will look like once it's installed. Next, well give you a couple of measurements to assist you with selecting accessories for your new hitch. In the center of the hitch pinhole to the outermost edge of the bumper, is seven inches. From the top of the receiver tube, to the ground is 10 inches. This will assist you with selecting accessories, such a drawbar, a bike rack or cargo carrier. more
6/4/2012 1:46:12 PM
Trailer Hitch Installation - 2012 Chrysler 200 - Curt- Video
Today on this 2012 Chrysler 200, we are going to install part number 11133 from Curt. Alright this is what the hitch looks like once installed on a vehicle. Next we'll go ahead and give you some measurements that will help you out in selecting some accessories such as a bicycle rack or a cargo carrier. From the center of the hitch pin hole, to the edge of the bumper is going to be 4 inches, and from the top of the receiver opening down to the ground is going to be 11 inches. Now I'll go ahead and show you how the hitch is installed. Now the first thing you do is fish wire a couple of bolts into the frame. more
5/17/2012 4:16:05 PM
Trailer Hitch Installation - 2005 Chrysler Town and Country - Hidden Hitch- Video
Today on our 2005 Chrysler Town and Country well be installing Hidden Hitch part number 87719. This is what our hitch will look like once its installed. Now, we can go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 3 inches. From the top of the receiver tube to the ground is 12-1/4 inches. This will assist you with selecting accessories such as a drawbar, a bike rack or a cargo carrier. more
5/3/2012 11:11:29 AM
Trailer Hitch Installation - 2005 Chrysler Town and Country - Draw-Tite- Video
Today on our 2005 Chrysler Town and Country well be installing the Draw-Tite hitch part number 75305. This is what our hitch will look like once its installed. Now, we can go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 3 inches, from the top of the receiver tube to the ground is 12-1/4 inches. This will assist you in selecting accessories such as drawbar, a bike rack, or a cargo carrier. Now, lets go ahead with installation. more
5/3/2012 11:10:25 AM
Trailer Hitch Installation - 2006 Chrysler Pacifica - Hidden Hitch- Video
Today on our 2006 Chrysler Pacifica, we're going to install hidden hitch, part number 87432. First, will be to remove the spare tire before you can begin installation. We've already gone and done that. Our next step will be put a safety strap under the exhaust as we'll need to lower it, but we don't want it to fall too far and damage the exhaust, so using a safety strap will help hold the exhaust. Then to remove the exhaust, we're going to remove the rubber isolators, easiest way to do this is to spray each isolator with a little spray lubricant and simply pry it off the metal stud of the muffler. Now we can use our safety strap to lower the exhaust to give us access to the frame. more
4/27/2012 3:25:53 PM
Trailer Hitch Installation - 2006 Chrysler Pacifica - Draw-Tite- Video
Today on our 2006 Chrysler Pacifica, we're going to install the draw tight hitch, part number 75522. First, will be to remove the spare tire before you can begin installation. We've already gone and done that. Our next step will be put a safety strap under the exhaust as we'll need to lower it, but we don't want it to fall too far and damage the exhaust, so using a safety strap will help hold the exhaust. Then to remove the exhaust, we're going to remove the rubber isolators, easiest way to do this is to spray each isolator with a little spray lubricant and simply pry it off the metal stud of the muffler. Now we can use our safety strap to lower the exhaust to give us access to the frame. more
4/27/2012 3:24:54 PM
Trailer Hitch Installation - 2007 Chrysler Pacifica - Hidden Hitch- Video
Today on our 2007 Chrysler Pacifica, we're going to install hidden hitch, part number 87432. Here are a couple measurements that will be useful when selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost point of the bumper is three inches, and from the top of the receiver tube to the ground is 11 inches. Now let's go ahead with our installation. As for the instructions, we've gone ahead and removed the spare tire ease of installation. Before we can begin installing the hitch, we'll need to lower the exhaust. more
4/27/2012 2:36:03 PM
Trailer Hitch Installation - 2007 Chrysler Pacifica - Draw-Tite- Video
Today on our 2007 Chrysler Pacifica, we're going to install draw tight hitch, part number 75522. Here are a couple measurements that will be useful when selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost point of the bumper is three inches, and from the top of the receiver tube to the ground is 11 inches. Now let's go ahead with our installation. As for the instructions, we've gone ahead and removed the spare tire ease of installation. Before we can begin installing the hitch, we'll need to lower the exhaust. more
4/27/2012 2:35:11 PM
Trailer Hitch Installation - 2011 Chrysler 200 - Curt- Video
Today on this 2011 Chrysler 200 we're going to install part number C11133 from Curt. Next we'll go ahead and give you some measurements that will help you out in selecting some accessories such as a cargo carrier or a bicycle rack. From the top of the receiver opening down to the ground will be 10-1/2 inches and from the center of the hitch pin hole to the edge of the bumper will be 4-1/2 inches. Now we'll go ahead and show you how the hitch is installed. We'll go ahead and show you where the hitch installs. It's going to use this one existing hole on the outside here and two of these existing holes on the inside of the frame. more
4/9/2012 1:55:14 PM
Trailer Hitch Installation - 2012 Chrysler Town and Country- Video
Today on this 2012 Chrysler Town and Country were going to install a hidden hitch part #: 87451. This will be comparable to the draw type hitch part #: 75579. Here are a couple of measurements that will assist you in selecting accessories for your new hitch. from the center of the hitch pinhole to the outermost point of the bumper is 6 inches. From the top of the receiver tube to the ground is 11 and inches. Now lets go ahead with the installation. more
2/27/2012 12:41:18 PM
Trailer Hitch Installation - 2012 Chrysler Town and Country 13364- Video
Today on our 2012 Chrysler Town and Country were going to install a curt hitch part #: 13364. Here are a couple of measurements that will assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost point of the bumper is 4 and a quarter inches, from the top of the receiver tube to the ground is 12 inches. This will assist you with selecting accessories. Now lets go ahead with the installation. Before we can install our hitch well first need to lower the vehicle exhaust. more
2/27/2012 12:37:57 PM
Trailer Hitch Installation - 2004 Chrysler PT Cruiser- Video
Today is 2004 Chrysler PT Cruiser; were going to install part number 60818 from Hidden Hitch. This also applies to part number 24759 from Draw-Tite. This what the hitch looks like when its installed on the vehicle, next well give you some measurements that will help you out in selecting from the accessories such as a ball out, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground on this particular vehicle is going to be 9 inches. And from the center of a hitch pinhole to the outside edge of the bumper is going to be 3inches. Now Ill go ahead and show you how the hitch is installed. more
1/11/2012 3:21:03 PM
Trailer Hitch Installation - 2005 Chrysler Pacifica- Video
Today on this 2005 Chrysler Pacifica, we are going to be installing Hidden Hitch part number 87432 and this installation with also apply to Draw-Tite hitch part number 75522. Before we get started with our installation, we are going to go ahead and give you a couple of final installed dimensions which are going to help make choosing your hitch accessories a little easier. From the top of the receiver tube opening to the ground, is going to measure 11-1/2 inches and from the center of the pin hole to clear the rear edge of the bumper is going to measure about 3-1/2 inches. And now we will go ahead and move onto our installation. OK, the first thing we have done is gone ahead and lowered down the spare tire just to give us a little more working room. We are starting off over in the passenger side, we are going to go ahead and lower down the exhaust first. If you do have dual exhaust you will need to do this on both sides. more
12/8/2011 10:28:13 AM
Trailer Hitch Installation - 2006 Chrysler 300C- Video
Today we will be working on a 2006 Chrysler 300C. We will be installing Curt hitch part number 13465. Here are a couple of measurements that will assist you in ing accessories for your new hitch. From the center of the hitch pin hole to the outermost point of the bumper is 6-1/2 inches. From the top of the receiver tube to the ground is 10-3/4 inches. This will assist you with ing accessories such as a draw bar, bike rack, or cargo carrier. Now let us go ahead with the installation. Before we install the hitch, we are going to have to lower the exhaust. Before we remove the exhaust hangers, I will take a safety strap fit it across the exhaust so it does not fall any further than necessary. Before we remove the exhaust hangers, we are going to spray the exhaust hanger studs down with a spray lubricant, I am using WD-40. This will make it easier to remove and reinstall later. I am going to do that for each of the rubber hangers. 0:57 more
8/1/2011 8:55:43 AM
Trailer Hitch Installation - 2001 Chrysler Sebring- Video
Today on this 2001 Chrysler Sebring we are going to install part number 60947 from Hidden Hitch. This is what the hitch looks like when it is installed on the vehicle. Now we will give you some measurements that will help you out in ing some accessories for this such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin to the outside edge of the bumper itself is going to be 5-3/4 inches. And from the top of the receiver tube down to the ground is going to be 11 inches. Now we will go ahead and show you how the hitch gets installed. 0:28 more
6/2/2011 10:32:20 AM
Trailer Hitch Installation - 2009 Chrysler Aspen- Video
Today on this 2009 Chrysler Aspen we are going to install part number 87562 from Hidden Hitch. This also applies to part number 75162 from Draw-Tite. This is what the hitch looks like when it is installed on the vehicle. And next we will give you some measurements that will help you out when ing some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground is going to be 21 inches on this particular vehicle. And the hitch pin hole is actually going to be 1/2 an inch past the edge of the bumper cover. Alright, now let us go ahead and show you how this gets installed on the vehicle. 0:32 more
3/11/2011 1:45:09 PM
Trailer Hitch Installation - 2004 Chrysler Town and Country- Video
Today on this 2004 Chrysler Town and Country with stow and go seating, we are going to be installing Draw-Tite hitch part number 75305. And this installation will also apply to Hidden Hitch part number 87719. Before we get started with our hitch installation, we are going to go ahead and show you a couple of the final install dimensions which will help make choosing your hitch accessories a little bit easier. From the top of the receiver tube opening to the ground is going to measure 12-1/4 inches. And from the center of the pin hole, to clear the rear edge of the bumper is going to measure approximately 6-1/2 inches. Alright, now we will go ahead and move on to our hitch installation. 0:33 more
1/24/2011 1:41:40 PM
Trailer Hitch Installation - 2005 Chrysler Pacifica C12262- Video
Today on this 2005 Chrysler Pacifica, we are going to install part number 12262 from Curt. This is what the hitch looks like when it is installed. Now we will go ahead and give you some measurements. From the top of the receiver opening down to the ground is going to be 11-3/4 inches on this particular vehicle. And from the center of the hitch pin hole to the outside edge of the bumper is going to be 6 inches. Alright, next we will go ahead and show you how it gets installed. 0:23 more
1/24/2011 11:53:38 AM
Trailer Hitch Installation - 2010 Chrysler Town and Country- Video
Today on this 2010 Chrysler Town and Country we are going to be installing Hidden Hitch part number 87451 and this installation will also apply for Draw-Tite hitch part number 75579. Before we get started we are going to give you a couple of final installed dimensions which will help make choosing your hitch accessories a little bit easier. From the top of the receiver tube opening to the ground is going to measure 12-1/ 2 inches and from the center of the pin hole to clear the rear edge of the bumper is going to be approximately 7 inches. Now we will move on to the hitch installation. 00:30 more
10/13/2010 10:40:16 AM
Trailer Hitch Installation - 2008 Chrysler Sebring- Video
Today on this 2008 Chrysler Sebring Sedan we will be installing Draw-Tite hitch part number 36448. This installation will also apply to Hidden Hitch part number 90166. Starting off underneath the vehicle, the first thing we are going to do is lower the exhaust down. We just want to remove this rear most hanger on the passenger side. :22 more
8/25/2010 4:07:32 PM
Trailer Hitch Installation - 2007 Chrysler 300- Video
Today on this 2007 Chrysler 300 we are going to be installing Curt hitch part number 13465. We are underneath the vehicle, the first thing we want to do is lower down the exhaust. Depending on your model you may have a single exhaust or a dual exhaust. On this particular vehicle we have a single exhaust. There is a hanger here at the rear side of the exhaust and a second one here at the forward side that we want to remove as well. If we follow forward we need to lower down these two hangers here as well. On the rear hanger some models will have this grounding strap, you want to make sure you take that off as well before you lower the exhaust down. :39 more
7/23/2010 12:18:26 PM
Trailer Hitch Installation - 2009 Chrysler Town and Country- Video
Today we are going to install part number 36455, a Draw-Tite Class II receiver hitch, on a 2009 Chrysler Town and Country. This hitch is going to attach to the frame by using these bolts right here. So we will take these bolts out and they will be reused in the installation of the hitch. As you can see, on the passengers side the exhaust is blocking our access to these bolts. So we will need to get that out of the way. This is going to be the first of two exhaust hangers we are going to take down we will start taking this one off first. OK, we have got our exhaust down and out of the way. We actually put a little strap on it just to hold it out of the way so it is a little easier to see what is going on. When we undo the flash bolt right here, this is actually connected to a bracket inside the frame for the bumper, so this actual part of the bumper here - it is actually going to - when we let go of this bolt the bracket is going to tilt up inside the frame. So you want to take care when you take out the bolt to be careful you do not move the bracket around too much. more
5/18/2009 9:55:22 AM
Trailer Hitch Installation - 1997 Chrysler Concorde- Video
Today we are going to be installing hitch part number 36170 from Draw-Tite on a 1997 Chrysler Concorde. The instructions do not state this, but the first thing I am going to do is actually to lower the exhaust off the two hangers. There is one here at the rear and one a little bit more forward. We are going to go ahead and lower the exhaust off those two. It is going to give us a little bit more working room. To lower the exhaust I am going to go ahead and just lower the two bolts on each hanger. And now that I have got the exhaust lowered, I am going to remove the inboard side endcap bolt here on the end of the frame rail. What we are going to do is actually replace that with a new bolt and reverse it and turn where the head is on this side, as opposed to the nut. That is going to give us a little more room when we go to put the hitch up into place and drill our holes. And in that bolts place, we are going to go ahead and put the new 3/8 bolt with a conical-tooth washer. And we want to make sure the head of the bolt is on the forward side of the frame. That is going to give us extra room when we go to drill our holes later. And we are going to reuse the existing nut that was already in place there, and then go ahead and tighten that down. And then here on the passengers side, we are going to remove both the inboard and outboard side ones. Those are actually going to provide attaching points for the trailer hitch. more
4/1/2009 12:13:21 PM
Filter Videos
Filter Videos
