Rhino Rack Roof Rack Review - 2014 Toyota Camry- Video

Today on our 2014 Toyota Camry, we're going to be test-fitting the Rhino Rack Vortex Aero Roof Rack System in silver. We'll begin our test-fit by assembling one of the fit kits. We've got our Aero Blade here, part number RRVA118S-2. We have our Foot Pack, part number RRLKVA, and our Fit Kit, part number DK321. We'll go ahead and assemble this for you. That way you've got an idea how to do it at home. more

Watch Video

10/16/2014 3:20:54 PM

Rhino Rack Roof Rack Review - 2014 Toyota Camry RRVA118B-2- Video

Today on our 2014 Toyota Camry we're going to be test fitting the Rhino-Rack Vortex Aero Roof Rack System in black part numbers RRVA118B-2 for our Aero Bar RRRLKVA for our foot pack and DK321 for our fit kit. We went ahead and assembled an installed the rest of the foot packs but I'll go ahead and show you how to do it on this one. The arrow here on the bottom of the bracket is going to face toward the outside of your vehicle. You also have an arrow on your pad here and that's going to be facing the front of the vehicle. We'll go ahead and press this on and move our bolt here, lay our clip in place and re-install our bolt. With that done we'll go ahead and turn our bar over here, remove the end cap, we'll then take and slide the block here into the channel. With that done we need to get our strip length. These will be included with your kit. more

Watch Video

10/16/2014 3:14:31 PM

Thule Traverse Roof Rack Installation - 2014 Toyota Camry- Video

Today on our 2014 Toyota Camry we'll be test fitting the Thule Traverse Roof Rack System using part numbers THLB50, TH480 and THKIT1438. With everything assembled according to the included instructions, we'll begin our test fit with the front doors open on our car. We'll place the front load bar onto the front of our roof and we'll need to measure 9 inches from the first part of the glass here at the front window to the leading edge of our foot pack. We'll need to make this measurement on both the passenger and driver's side of the vehicle to ensure the front bar is perpendicular to the roof of our Camry and the pads contour to the roof line. With the bar in position, we can use the included tensioning tool to tighten down the silver bolt on the inside of the foot which will bring the clips up tightly against the roof line. Now, we'll need to alternate tightening down each side a little bit at a time so the bar doesn't favor one side of the vehicle. Once that's tightened down and secure, we can place the rear bar onto the rear of our roof. We'll then need to measure the load bar spread. more

Watch Video

7/7/2014 10:52:59 AM

Yakima Q Tower Roof Rack Installation - 2014 Toyota Camry- Video

Today on our 2014 Toyota Camry we're going to be test fitting the Yakima Q Towers Roof Rack System using the 58" Round Bars. We'll use part numbers Y00409, Y00605, Y00716 and Y00124. With our rack assembled according to the manufacturer's instructions, we'll begin our test fit by opening our front door and placing the front half of our roof rack onto the front roof line. Per the Yakima fit guide we'll measure 8" from the rear edge of our windshield to the leading edge of our foot pack. We'll do this measurement on both sides to be sure we have our feet in line with each other. With both of our feet in line we'll now pull down on the black lever located on each foot pack to secure our clips around the underside of our roof line. With the front half of our rack secure we'll close our front doors, open our rear doors and grab the rear portion of our rack. We'll place it onto the rear portion of our roof. more

Watch Video

7/1/2014 8:21:51 AM

Yakima Q Tower Roof Rack Installation - 2014 Toyota Camry Y00124- Video

Today on our 2014 Toyota Camry, we are going to be test fitting the Yakima Q Towers roof rack system using the 48 inch round bars. We'll use part numbers Y00408, Y00605, Y00716 and Y00124. With our roof rack assembled according the manufactures instructions, we'll begin our test fit by opening the front doors of our Camry and grabbing the front half of our rack. We'll place it on to the front roof line of our vehicle. For Yakimas fit guide, we are going to measure 8 inches from the rear edge of our wind sheield to the front edge of our foot peg. We want to take this measurement on both sides to be sure that we have our feet in line with each other. With our measurement done on both sides, we'll now pull down on the black levers which will tighten our clips around the underside of our roof line securing our rack to our vehicle. With the front hatch secure, we'll shut our front doors, open our rear doors and grab the rear half of our rack. We'll place it on to the rear portion of our roof. more

Watch Video

6/19/2014 4:22:53 PM

  1