Summer Starts Here - Save up to 70%
Curt Trailer Hitch Installation - 2011 Ford Crown Victoria- Video
Shane: Hey guys, Shane here with etrailer.com.Today I have a 2011 Ford Crown Victoria, and I'm going to walk through how to install the Curt Class II trailer hitch receiver. Adding a Class II hitch on your vehicle. It doesn't allow you to put a cargo carrier, bike rack, maybe you want to pull a small trailer. Adding a bike rack, we're not going to have to load the bikes inside the vehicle, try to fit them in the trunk. Cargo carrier, we can put some cargo on the carrier to make more room inside the vehicle for our passengers.It's going to give us an 1.25" by 1.25" receiver tube opening, reinforced collar gives us a little extra stability there. Hitch pin hole is going to be 1/2" in diameter. more
5/26/2020 2:02:07 PM
Trailer Hitch Installation - 2006 Ford Crown Victoria - Curt- Video
Today on this 2006 Ford Crown Victoria, we're going to install part number 13707 from Curt. All right. This is what the hitch looks like when it's installed on the Crown Victoria. Next we'll go ahead and give you some measurements that will help you out in selecting some accessories such as a draw bar, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground will be about 13 and 1/4 inches. Now from the center of the hitch pin hole to the edge of the bumper will be about 5 and 1/2 inches. Now we'll go ahead and show you how the hitch is installed. To start off, we'll go ahead and get our vehicle ready to install our hitch. more
10/30/2014 8:45:34 AM
Trailer Hitch Installation - 2007 Ford Crown Victoria - Curt- Video
Today on this 2007 Crown Victoria, were going to install part number 13707 from Curt. Now this is what the hitch looks like once its installed on the vehicle. Next well go ahead and give you some measurements to help you out in selecting some accessories such as ball mount, a bicycle rack, or cargo carrier. From the top of the receiver opening down to the ground will be 13-1/4 and from the center of the hitch pin hole to the edge of the bumper will be about 5-3/8.Now well go ahead and show you how the hitch is installed. First thing were going to do is to get underneath the vehicle and our two straps have to be moved from the frame. Well reattach these straps at the end of the install. more
2/15/2013 2:18:41 PM
Trailer Hitch Installation - 2003 Ford Crown Victoria- Video
Today on this 2003 Ford Crown Victoria we are going to be installing Curt hitch part number 13707. We are underneath the vehicle and we are taking a look at the driver side frame rail. You can see there is really not much going on at the bottom of the frame We are actually going to have to take the hitch and clamp it up into position. We are going to use it as a template to drill out all four holes that we are going to be using to attach the hitch to the frame. This particular vehicle has some grounding clips that attach here at the end of the frame rail that we want to remove before we clamp the hitch up into position. 00:28 more
5/27/2010 8:23:55 AM
Trailer Hitch Installation - 1999 Ford Crown Victoria- Video
Today we are going to be installing Curt hitch part number 13707 on a 1999 Ford Crown Victoria. OK, underneath the vehicle, we are going to go ahead and point out the mounting locations for the trailer hitch. There is an opening right here at the end of the frame rail that we can use to actually - we are going to take some C-clamps and clamp the hitch up into place. Then we can go ahead and drill our holes out, using the hitch as a template. The vehicle does have these ground clips at the end of the frame we want to go ahead and remove those before we get started, and we will put them back up once the installation is complete. more
6/12/2009 12:18:31 AM
Filter Videos
Filter Videos
