Summer Starts Here - Save up to 70%
Trailer Hitch Installation - 2007 Buick Rendezvous - Curt- Video
Today on this 2007 Buick Rendezvous, we're going to show you Curt Trailer Hitch Receiver class III, with a 2-inch opening, part number 13469. All right. This is what the hitch looks like when it's installed on our Rendezvous. As you could see, it actually sits almost all the way underneath the bumper due to the vehicle's construction. even though it does sit pretty far back, it is a bit visible. Okay. Now, it does have a reinforced collar around the front edge of the receiver, makes it look nice. more
6/30/2015 2:06:27 PM
Trailer Hitch Installation - 2006 Buick Rendezvous - Hidden Hitch- Video
Today, on our 2006 Buick Rendezvous, we'll be installing the Hidden Hitch, part number 90158. Here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch, such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper, it's approximately 5-1/2 inches. From the top of the opening in the hitch to the ground is approximately 12-3/4 inches. Now, let's go ahead and install our hitch. To begin with, let's go ahead and point out the locations that we'll be using to mount our hitch. more
11/18/2014 4:17:34 AM
Trailer Hitch Installation - 2005 Buick Rendezvous - Draw-Tite- Video
Today on our 2005 Buick Rendezvous, we're going to be installing the Draw-Tite trailer hitch receiver, part number 75430. Now here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple measurements in helping you choose some accessories for hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is approximately 6 1/2 inches. From the top of the opening in the receiver to the ground is approximately 12 3/4 inches. Now let's go ahead and install our hitch. Let's go ahead and begin here underneath the vehicle and we're going to point out our mounting locations that we'll be using. more
10/25/2014 12:01:57 PM
Trailer Hitch Installation - 2006 Buick Rendezvous - Draw-Tite- Video
Today in our 2006 Buick Rendezvous well be installing the Draw-Tite Max-Frame Trailer Hitch Receiver in a Class III with a two-inch opening on the receiver, part number 75138. Heres what our hitch looks like installed on our vehicle. We will go ahead and give you a couple of measurements in helping you choose some accessories for your hitch such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the outmost edge of the bumper is approximately 5 inches. From the top of the opening in the receiver to the ground is approximately 12 inches. Lets go ahead and install our hitch. Well start here underneath the rear bumper fascia at the rear of the vehicle. There are a total of five push-in retaining clips that well need to remove first. more
10/25/2013 1:04:07 PM
Trailer Hitch Installation - 2004 Buick Rendezvous - Draw-Tite- Video
All right, today on this 2004 Buick Rendezvous, were going to install part number 75430 from Draw-Tite. All right, this is what the hitch looks like when its installed on the vehicle. Next well give you some measurements thatll help out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down the ground will be about 13-1/4 inches. From the center of the hitch pinhole to the edge of the bumper will be about 5-1/2 inches. Now Ill go ahead and show you how the hitch is installed. Before we install the hardware, well show how it looks on the hitch. Youll see you have the bolt and blocks will be inside the frame and then go through the hitch and on the bottom of the hitch, youll have the conical tooth washers and nuts. more
1/28/2013 1:48:32 AM
Trailer Hitch Installation - 2003 Buick Rendezvous - Hidden Hitch- Video
Today on this 2003 Buick Rendezvous were going to install part number 90158 from Hidden Hitch. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground is going to be about 13 inches. From the center of the hitch pin hole to the edge of the bumper is going to be about five and three-eighths. Now well go ahead and show you how the hitch is installed. more
1/25/2013 9:14:04 AM
Trailer Hitch Installation - 2003 Buick Rendezvous - Draw-Tite- Video
Today on this 2003 Buick Rendezvous were going to install part number 36425 from Draw Tite. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground is going to be about 13 inches. From the center of the hitch pin hole to the edge of the bumper is going to be about five and three-eighths. Now well go ahead and show you how the hitch is installed. more
1/25/2013 9:13:54 AM
Trailer Hitch Installation - 2004 Buick Rendezvous- Video
Today on this 2004 Buick Rendezvous we will be installing Draw-Tite hitch part number 36425. This installation will also apply for Hidden Hitch part number 90158. We are underneath the vehicle near the bumper, we are looking at the driver side frame rail. As you can see we have two large oblong holes at the end of the frame rail and we are going to be using both of those as attaching points for our trailer hitch. We will be placing carriage bolts and blocks up inside the frame and pulling it back down into position for both of those locations. That is going to be the same on the passenger side as well. If you notice further rearward we have this lip that is attaching the body to the bumper. We are going to be drilling four holes, two per side, to attach the trailer hitch to as well. What we want to do first is put the hardware into the frame, get the hitch up into position, and we will use the hitch as a template to drill those holes out. 00:47 more
3/29/2010 5:40:57 AM
Filter Videos
Filter Videos
