SportRack Super EZ Hitch Bike Rack Review - 2014 Chevrolet Sonic- Video

Today on our 2014 Chevy Sonic we'll be test fitting the SportRack Super EZ Platform-Style 2 Bike Rack part number SR2901LR. We'll begin our test fit by sliding the shank of the bike rack in to the opening of the hitch. After lining up the pin holes we'll thread in our anti-rattle bolts and tighten it down using a wrench. The bike rack secured we'll go over a few clearance measurements to see how the two fit together. We have about thirteen inches of ground clearance. Closest part of the bike rack to the closest part of the vehicle is about six inches and we've added about twenty five inches to the overall length of our Sonic. We'll now go ahead and pull the three pins at the base of the bike rack to pull down the wheel cradles as well as the mast. more

Watch Video

1/20/2014 5:29:23 PM

Prorack 4 Hitch Bike Rack Review - 2014 Chevrolet Sonic- Video

Today on our 2014 Chevy Sonic, we'll be testing fitting the Prorack Hitch-Mounted 4-Bike rack, part number PR8062404. We'll begin our test fit by sliding the shank of the bike rack into the opening of the hitch. After lining up the pin holes, we'll thread our anti-rattle bolt into the pin holes and tighten it down with a wrench. We'll then secure it with a clip on the other side. With the bike rack secured, we'll go over a few clearance measurements to see how the two fit together. We have about 10 inches of ground clearance. The closest part of the bike rack to the closest part of the vehicle is about 5 inches away, and we've added about 30 inches to the overall length of our Sonic. With the bike rack in this position, you can see that we do have access to the vehicle's trunk. To be able to load larger cargo into our trunk, we can remove the pin at the base of the bike rack and tilt the mast down. more

Watch Video

1/20/2014 5:29:15 PM

Yakima StickUp 2 Hitch Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe we'll be test fitting the Yakima StickUp 2 Bike Hitch Mounted Bike Rack part number Y02420. To begin our test fit we'll slide the shank of the bike rack in to the receiver tube of the hitch, line up the pin holes and thread in our anti-rattle bolt tightening it with a wrench. Now, we'll go over a few clearance measurements. We have about twenty one and a half inches of ground clearance. Closest point of the bike rack to the rear of our Tahoe is about seven inches and we've added about fourteen inches to the overall length of our vehicle. We'll pull the pin with the red knob at the base of our bike rack to allow our bike rack to unfold. With the bike rack in this position we have full access to our rear hatch door. more

Watch Video

1/20/2014 12:01:34 PM

Thule Hitching Post Pro Hitch Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe, we'll be test fitting the Thule Hitching Post Pro, folding and tilting 4 bike rack with anti-sway, fitting the 1 1/4 and 2 inch hitches, part number TH934XTR. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of the hutch. Line up the pin hole and thread in our anti-rattle bolt, tightening it with a wrench. Now we'll go over some clearance measurements. We have about 20 1/2 inches of ground clearance because it's one of the bike rack to the rear of our Tahoe is about 8 inches and we've added about 17 inches to the overall length of our vehicle. We'll pull the safety pin at the base of the mast and our bike rack to tilt the way from our vehicle. This gives us full access to our rear hatch door. With the mast back in it's up right position and the pin reinstalled, we'll pull the pin at the top of the mast to swing out our door alarms. With these out, we've added about 39 1/2 inches to the overall length of our Chevrolet Tahoe. Well under our cradle straps to expose our cradles. We'll grab our bike, place it on to the frame cradles and secure it by tightening each strap. With our bike all loaded up, that completes today's test fit of the Thule Hitching Post Pro part number TH934XTR on our 2013 Chevrolet Tahoe. more

Watch Video

1/20/2014 12:00:18 PM

Thule Doubletrack Hitch Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe, we'll be test fitting the Thule Doubletrack Platform Style 2 Bike Rack for inch and a quarter and 2 inch hitches, Part Number TH990XT. We'll begin our test fit by sliding the shank of the bike rack into the receiver tube of the hitch. We'll line up the pin holes and thread in our anti-rattle bolt tightening it with a wrench. Now we'll go over a few clearance measurements. We have about 20 and a half inches of ground clearance. The closest point of the bike rack to the rear of our Tahoe is about 6 inches. more

Watch Video

1/20/2014 12:00:11 PM

SportRack Super EZ Hitch Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe, we'll be test fitting this Sport Rack Super EZ Platform bike rack for inch-and-a-quarter and 2-inch hitches, part number SR2901LR. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of the hitch. We'll line up our pin holes and thread in our anti-rattle bolt, tightening it with a wrench. Then we can install the lock on the other side. Please keep in mind that with the factory hitch and the seven-way connector, the lock is a tight fit, especially with the key sitting in the lock. Now we'll go over some clearance measurements. We have about 23-1/2 inches of ground clearance. The closest point of the bike rack to the rear of our Tahoe is about 7 inches. more

Watch Video

1/20/2014 11:59:58 AM

SportRack Hitch Platform 4 Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe, we'll be test fitting the SportRack 4-Bike Carrier for 2-inch hitches, part SR2902. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of the hitch, line up the pin hole, and thread in our anti-rattle bolt, tightening it with a wrench. Now, we'll go over a few clearance measurements. We have about 27-1/2 inches of ground clearance here at the very rear of our bike rack. We have about 23-1/2 inches of ground clearance at our support bar. The closest point of the bike rack to the rear of our Tahoe is about 9-1/2 inches, and we've added about 44-1/2 inches to the overall length of our vehicle. We'll pull the 3 pins at the base of each 2-bike configuration. This allows the different parts of the bike rack to unfold. With the bike rack in this position, we have full access to our rear hatch. more

Watch Video

1/20/2014 11:59:52 AM

Softride Element Hitch Mounted Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe, well be test fitting the Softride Element Parallelogram Tilting Four Bike Rack for inch and a quarter and two inch hitches, part number SR26248. We slide the shank of the bike rack into the receiver tube of the hitch, line up our pinholes and thread in our anti-rattle bolt, tightening it with a wrench. Now well go over a few clearance measurements. We have a ground clearance of about twenty-one inches. The closest point of the bike rack to the rear of our vehicle is about five inches. And weve added about thirteen inches to the overall length of our Chevrolet Tahoe. more

Watch Video

1/20/2014 11:59:47 AM

Softride Dura Hitch Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe, we'll be test fitting the Softride Dura Parallelogram Tilting 4 Bike Rack for inch and a 1/4 and 2 inch hitches, Part Number SR26247. We'll begin our test fit by sliding the shank of the bike rack into the receiver tube of the hitch. We'll line up our pin holes and thread in our anti-rattle bolt tightening it with a wrench and then installing our lock. Now we'll go over a few clearance measurements. We have about 20-1/2 inches of ground clearance. The closest point of the bike rack to the rear of our vehicle is about 6-1/2 inches. more

Watch Video

1/20/2014 11:59:43 AM

Thule Apex 4 Hitch Bike Rack Review - 2014 Chevrolet Sonic- Video

Today on our 2014 Chevy Sonic we'll be test fitting the Thule Apex 4 Bike Rack part number TH9025. We'll begin our test fit by sliding the shank of the bike rack in to the opening of the hitch. After allowing the integrated hitch pin to fall into place we'll then turn the black knob to engage the anti-rattle device. With the bike rack secured we'll go over a few clearance measurements to see how the two fit together. We have about twelve inches of ground clearance. Closest part of the bike rack to the closest part of the vehicle is about one and a half inches away and we've added about twelve inches to the overall length of our Sonic. We can now lift up on the grade lever at the top of the mast and swing the cradle arms out. more

Watch Video

1/20/2014 11:30:00 AM

Swagman Titan Hitch Bike Rack Review - 2014 Chevrolet Sonic- Video

Today on our 2014 Chevy Sonic, we'll be test fitting the Swagman Titan Hitch Mounted 4 Bike Rack Part Number S63410. We'll begin our test fit by sliding the shank of the bike rack into the opening of the hitch. After lining up the pin holes, we'll thread our anti-rattle bolt through the pin holes and then tighten it down with a wrench. With the bike rack secured, we'll go over a few clearance measurements to see how the 2 fit together. We have about 14 inches of ground clearance. Closest part of the bike rack to the closest part of the vehicle is about 5 inches away. more

Watch Video

1/20/2014 5:29:35 AM

Swagman Jackknife Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe we'll be test-fitting the Swagman Jackknife 2-Bike Rack for 1 1/4 Inch and two-Inch hitches, part number S63450. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of the hitch. We'll line up the pin hole and thread in our anti-rattle bolt, tightening it with a wrench, and installing the clip on the other side. Now this bike rack does come with a lock to attach to your anti-rattle bolt, but it makes contact with our 7-way connector. So we'll be using the other bolt, which simply uses a pin. Now we'll go over a few clearance measurements. We have about 20 1/2 inches of ground clearance. The closest point of the bike rack to the rear of our Tahoe is about 10 inches. more

Watch Video

1/7/2014 4:30:44 PM

Pro Series Q-Slot 2 and 4 Bike Hitch Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe we'll be test fitting the pro-series Q-slot platform style two bike rack for two inch hitches, part number PS63138. Please keep in mind that there is another rack that's a two bike add on that will attach to this two bike rack and make it a four bike rack. We'll begin our test fit by sliding the shank of the bike rack into the receiver tube of the hitch. We'll line up the pinholes and thread in our anti-rattle bolt, tightening it with a wrench. Now we'll go over a few clearance measurements. We have a ground clearance of about 21 inches. The closest point of the bike rack to the rear of our Tahoe is about nine inches. more

Watch Video

1/7/2014 4:18:16 PM

Hollywood Racks Traveler 5 Hitch Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today, on our 2013 Chevrolet Tahoe, we'll be test-fitting the Hollywood Racks Traveler 5-Bike Rack for 2-inch Hitches, part number HR9200. To begin our test-fit, we'll slide the shank of the bike rack into the receiver tube of the hitch, line up the pin holes, and thread in our anti-rattle bolt tightening it with a wrench. Now, we'll go over a few clearance measurements. We have about twenty one inches of ground clearance. The closest point of the bike rack to the rear of our Tahoe is about eight inches, and we've added about sixteen inches to the overall length of our vehicle. We'll pull the pin and clip at the base of the bike rack and allow it to tilt away from our Tahoe. more

Watch Video

1/7/2014 3:45:50 PM

Hollywood Racks Traveler Hitch Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today, on our 2013 Chevrolet Tahoe, we'll be test-fitting the Hollywood Racks Traveler 4-Bike Rack for inch and a quarter and two inch hitches, part number HR8500. To begin our test-fit, we'll slide the shank of the bike rack into the receiver tube of the hitch. We'll line up the pin holes and thread in our anti rattle bolt, tightening it with a wrench. Now, we'll go over a few clearance measurements. We have about twenty one inches of ground clearance. The closest point of the bike rack to the rear of our Tahoe is about three and a half inches. more

Watch Video

1/7/2014 3:41:44 PM

Prorack 4 Hitch Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe, we'll be testing the Prorack 4-bike rack for inch and a quarter inch to two inch hitches. Part number PR8062404. To begin our testing, we'll side the shank of the bike rack into the receiver tubeof the hitch,we'll line up the pinhole and thread in our anti-ratlle bolt. tighten it with the wrench, and installing the clip on the other side. Now, we'll go over a few clearance measurements. We have about twenty-and-a-half inches of ground clearance that crosses far at the bike rack to the rear of the vehicle is about five inches, and we've added about 32 inches to the overall length of our Chevrolet Tahoe. We'll pull the pin and clip at the base of the bike rack and allow it to tilt aw3ay from the vehicle. This gives us full access to rear hatch door. more

Watch Video

1/7/2014 10:06:25 AM

Kuat NV Hitch Bike Rack Review - 2013 Chevrolet Tahoe- Video

Today on our 2013 Chevrolet Tahoe, we'll be test fitting the Kuat NV Aluminum Platform Style 12 Bike Rack for 2 inch hitches, Part Number N101. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of the hitch. Line up our pin holes and install our pin and lock. Here at the rear of the shank, we'll use the hand knob to secure the bike rack to the vehicle and engage our anti-rattle device. Now we'll go over some clearance measurements. We have about 21 1/2 inches of ground clearance. more

Watch Video

1/6/2014 3:52:31 PM

Swagman Titan Hitch Bike Rack Review - 1999 Chevrolet Blazer- Video

Today on our 1999 Chevrolet Blazer we'll be test fitting the Swagman Titan four bike carrier, part number S63410. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole and thread in our anti-rattle bolt, tightening with a wrench. Now, we'll go over some clearance measurements. We have about 16 and a half inches of ground clearance. The closest point of the carrier to the rear of our vehicle is about nine inches and we've added about 21 inches to the overall length of our Blazer. We'll pull the lever here at the base of the mast to allow our carrier to tilt away from our Blazer. This gives us full access to our cargo area by being able to open our rear hatch. With our mast back in it's upright position, we'll pull the lever at the top of the mast to swing out our dual arms. more

Watch Video

10/12/2013 10:27:35 AM

Softride Dura Hitch Bike Rack Review - 1999 Chevrolet Blazer- Video

Today on our 1999 Chevrolet Blazer we'll be test fitting the Soft Ride Dura Parallelogram Tilting four bike rack for inch and a quarter and two inch hitches, part number SR26247. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole and thread in our anti-rattle bolt, tightening it with a wrench, and installing the lock. Now we'll go over some clearance measurements. We have about thirteen and a half inches of ground clearance. The closest point of the carrier to the rear of our vehicle is about an inch. We've added about thirty-three inches to the overall length of our Blazer. We'll undo the cradle straps and with our cradles exposed, we'll place our bike onto the frame cradles. We'll secure it by tightening down each strap. One of the cool features of the Parallelogram is its ability to tilt with the bike loaded. If we pull the pin here at the top of the mast, we can tilt our carrier away from our vehicle. This gives us full access to the cargo area by being able to open our rear hatch. That completes today's test fit of the Soft Ride Dura Parallelogram, part number SR26247, on our 1999 Chevrolet Blazer. . more

Watch Video

10/12/2013 10:27:32 AM

Thule Vertex 4 Hitch Bike Rack Review - 2007 Chevrolet Silverado- Video

Today on our 2007 Chevrolet Silverado New Body, well be test fitting the Thule Vertex Four-Bike Carrier for inch and a quarter and two inch hitches: part number TH9029. To begin our test fit, well slide the shank of the carrier into the receiver tube of the hitch. Well line up the pinhole and thread in our anti-rattle bolt tightening it with a wrench. Well go over some clearance measurements. We have about seventeen inches of ground clearance. The closest point of our carrier to the rear of our vehicle is about four inches. Weve added about 14 inches to the overall length of our truck. Well pull the lever here at the base of our carrier to allow our carrier to tilt away from the vehicle. more

Watch Video

10/8/2013 3:39:27 PM

Thule Hitching Post Pro Hitch Bike Rack Review - 2007 Chevrolet Silverado New Body- Video

Today on our 2007 Chevrolet Silverado new body, we'll be test fitting the Thule Hitching Post Pro 4 Bike Rack with anti-sway, part number TH934XTR. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole, and thread in our anti-rattle bolt, tightening it with a wrench. Now, we'll go over some clearance measurements. We have about 16 inches of ground clearance. The closest point of the carrier to the rear of our truck is about 7-1/2 inches. We've added about 17 inches to the overall length of our vehicle. We'll pull the pin here at the base of the carrier to allow our carrier to tilt away from our truck. This gives us full access to the tailgate area of our vehicle. With the mast back in its upright position, we'll reinstall the pin and then pull the pin at the top of the mast to swing out our dual arms. more

Watch Video

10/8/2013 3:37:16 PM

Thule Apex 4 Hitch Bike Rack Review - 2007 Chevrolet Silverado New Body- Video

Today on our 2007 Chevrolet Silverado new body, well be test fitting the thule apex four-bike carrier for an inch and quarter and two inch hitches part number th9025. To begin our test fit well slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole, and allow the attached pin to fall into place. Here at the rear of the shank, well tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now well go over some clearance measurements. We have about 17 and a half inches ground clearance. The closest point of the carrier to the rear of our truck is about an inch. Weve added about 14 inches to the overall length of our Silverado. more

Watch Video

10/8/2013 3:36:03 PM

Kuat Sherpa Hitch Bike Rack Review - 2007 Chevrolet Silverado New Body- Video

Today, on our 2007 Chevrolet Silverado New Body, we'll be test fitting the Kuat Sherpa Aluminum Platform-Style Hitch Mounted 2 Bike Rack, part number S102. To begin our test fit, we'll slide the shank of the carrierinto the receiver tube of the hitch, line up the pin hole, and install our pin and lock. We'll move to the rear of the shank, and use the hand-knob to engage our anti-rattle device and secure our bike rack toour vehicle. Now, we'll go over some clearance measurements. We have about 20 inches of ground clearance. The closest point of the carrier to the rear of our truck is about 2 inches. more

Watch Video

10/8/2013 3:34:49 PM

Swagman Titan Hitch Bike Rack Review - 2007 Chevrolet Silverado- Video

Today on our 2007 Chevrolet Silverado new body, we'll be test fitting the Swagman Titan 4 Bike Carrier for 1-1/4and 2-inch hitches, part number S63410. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole and thread in our anti-rattle bolt. Now, we'll go over some clearance measurements. We have about 19-1/2 inches of ground clearance. The closest point of the carrier to the rear of our truck is about 2 inches. We've added about 21 inches to the overall lengthof our Silverado. We'll pull the lever at the base of the carrier to allow it to tilt away from our vehicle. This gives us full access to the bed of our truck by being able to fully open our tailgate. more

Watch Video

10/8/2013 1:07:21 PM

Softride Dura Hitch Bike Rack Review - 2007 Chevrolet Silverado New Body- Video

Today, on our 2007 Chevrolet Silverado new body we'll be test fitting the Softride Dura Parallelogram titling four bike rack for 1-1/4 inch and 2-inch hitches, part number SR26247. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pinhole and tread in our anti-rattle bolt, tightening it with a wrench and fitting the lock in place. Now, we'll go over some clearance measurements. We have about 16-1/2 inches of ground clearance. The closets point of the carrier to the rear of our truck is about 1-1/2 inches, and we've added about 34 inches to the overall length of our Silverado. We'll go ahead and undo our cradle straps and with our cradles exposed we'll place our bike onto the frame cradles. We'll secure it by tightening down each strap. We'll pull the pin on the passenger's side of the carrier up near the top, which allows our carrier to tilt away from the vehicle with the bike loaded keeping it parallel with the ground. This gives us access to the bed of our truck by being able to open our tailgate. That completes today's test fit of the Softride Dura Parallelogram, part number SR26247 on our 2007 Chevrolet Silverado new body. . more

Watch Video

10/8/2013 1:02:43 PM

Yakima DoubleDown Ace Hitch Bike Rack Review - 2005 Chevrolet Equinox- Video

Today on our 2005 Chevrolet Equinox, we'll be test fitting the Yakima DoubleDown Ace 4 Bike Rack, part number Y02451. To begin our test fit, we'll slide the shank of the rack into the receiver tube of the hitch, line up the pin holes, and insert the attached red pin. We'll then move to the back of the rack and use the hand knob to engage our anti-rattle device, which will secure our DoubleDown Ace to our Equinox. Next, we'll go over some key measurements. The ground clearance at the back of the rack is about 10 inches. The closest part of the DoubleDown Ace to our Equinox is about 3-1/2 inches. With the cradle arms folded down, we've added about 9 inches to the overall length of our Equinox. Next, we can pull the knob at the base of our rack to tilt the mast down. This allows us to gain access to our cargo area. more

Watch Video

9/27/2013 3:07:39 PM

Yakima DoubleDown Ace 2 Bike Rack Review - 2005 Chevrolet Equinox- Video

Today on our 2005 Chevrolet Equinox, we'll be test fitting the Yakima DoubleDown Ace two-bike rack, Part Number Y02450. To begin our test fit, we'll slide the shank of the rack into the receiver tube of the hitch, line up the pin holes, and insert the attached red pin. We'll then move to the back of the rack and use the hand knob to engage our anti-rattle device, which will secure our DoubleDown Ace to our Equinox. Next, we'll go over some key measurements. The ground clearance at the back of the rack is about 10 inches. The closest part of the DoubleDown Ace to our Equinox is about 3-1/2 inches. With the cradle arms folded down, we've added about 9 inches to the overall length of our Equinox. more

Watch Video

9/27/2013 3:07:32 PM

Thule Vertex 4 Hitch Bike Rack Review - 2005 Chevrolet Equinox- Video

Today on our 2005 Chevrolet Equinox we'll be test fitting the Thule Vertex Four Bike Carrier, part number TH9029. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of our hitch, line up the pin hole, and thread in our anti-rattle bolt, tightening it with a wrench. Now we'll go over some key measurements. We have elven inches of ground clearance. The closest part of the rack to our Equinox is about three inches. We have added twelve inches to the overall length of our Chevrolet Equinox. We'll pull the lever at the base of the carrier to allow our carrier to tilt away from the vehicle. This allows us to gain access to the cargo area of our vehicle by being able to open our rear hatch. With our mast back in its upright position, we'll pull the lever at the top of the mast to swing down the dual arms. With these out, we've added thirty-six inches to the overall length of our vehicle. We'll go ahead and undo the cradle straps to expose our cradles, place our bike onto the frame cradles, and secure it by tightening down each strap. With that done, our bike is all loaded up and we're ready to hit the road. That completes today's test fit of the Thule Vertex Four Bike Carrier, part number TH9029, on our 2005 Chevrolet Equinox. . more

Watch Video

9/27/2013 3:07:23 PM

Thule Hitching Post Pro Hitch Bike Rack Review - 2005 Chevrolet Equinox- Video

Today, on our 2005 Chevrolet Equinox, we'll be test fitting the Thule Hitching Post Pro Folding Tilting 4-Bike Rack with anti-sway, part number TH934XTR. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole, and thread in our anti-rattle bolt, tightening it with a wrench. Now we'll go over some key measurements. We have 9-1/2 inches of ground clearance. The closest point of the carrier to the rear of the Equinox is about 5 inches. We've added 16 inches to the overall length of our Equinox. more

Watch Video

9/27/2013 3:07:19 PM

Thule Helium Aero Hitch Bike Rack Review - 2005 Chevrolet Equinox- Video

Today on 2005 Chevrolet Equinox, we'll be test fitting the Thule Helium Aero 2 Bike Carrier, part number TH9042. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole, and allow the attached pin to fall into place. We'll then move to the rear of the shank and use the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now, we'll go over some key measurements. We have about 10 inches of ground clearance. The closest point of the carrier to the rear of the Equinox is about 2 inches. We've added about 16-1/2 inches to the overall length of our Chevrolet Equinox. We'll pull the lever at the base of the carrier to allow our carrier to tilt away from the vehicle. more

Watch Video

9/27/2013 3:07:13 PM

Thule Apex 4 Hitch Bike Rack Review - 2005 Chevrolet Equinox- Video

Today on our 2005 Chevrolet Equinox, we'll be test fitting the Thule Apex four bike carrier, part number TH9025. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole, and allow our attached pin to fall in place. We'll then move to the rear of the shank and use the hand knob to secure our bike rack to our vehicle, and engage our anti-rattle device. Now we'll go ahead and go over some key measurements. We have about 12 1/2 inches of ground clearance. The closest point of the carrier to the rear of the Equinox is about two inches. We've added twelve inches to the overall length of our Chevrolet Equnox. We'll pull the lever at the base of the mast to allow our carrier to tilt away from our vehicle. This allows us to gain access to the cargo area of the Equinox by openingour rear hatch. With our mast back in it's upright position, we'll pull the lever at the top of the mast to swing out our dual arms. more

Watch Video

9/27/2013 3:07:08 PM

Swagman Titan Hitch Bike Rack Review - 2005 Chevrolet Equinox- Video

Today on our 2005 Chevrolet Equinox, well be test fitting the Swagman Titan Four Bike Carrier, part number S63410. To begin our test fit, well slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and thread in our anti-rattle bolt, tightening it with a wrench. Now well go over some key measurements. We have a ground clearance of 14 inches. The closest point of the carrier to the rear of our Equinox is about 6 inches. more

Watch Video

9/27/2013 3:07:04 PM

Hollywood Racks Traveler Hitch Bike Rack Review - 2012 Chevrolet Traverse- Video

Today, on our 2012 Chevrolet Traverse, we'll be test fitting the Hollywood Racks Traveler 4 bike rack, part number HR8500. We'll begin our test fit by sliding the shank of the bike rack into the opening of the hitch. We'll line up the pinholes, enter our anti-rattle bolt into the pinholes and tighten it down with a wrench. With our Hollywood Racks Traveler secured to our Traverse, we'll go over a few clearance measurements to see how the 2 fit together. We have about 16 1/2 inches of ground clearance. The closest part of our bike rack to the closest part of our Traverse is about 1/4 of an inch away. With the cradle arms folded down, we've added about 6 inches to the overall length of our Traverse. We can now pull the black pin at the top of the mast to swing the cradle arms out. With the cradle arms out, we've added about 29 1/2 inches to the overall length of our Traverse. To access the cargo area, we can pull the black pin at the base of the bike rack and tilt the mast down. more

Watch Video

9/19/2013 1:11:03 PM

Kuat NV Hitch Bike Rack Review - 2012 Chevrolet Traverse- Video

Today on our 2012 Chevrolet Traverse well be test fitting the Kuat NV platform style aluminum two bike rack part #: N101. Well begin our test fit by sliding the shank of the bike rack into the opening of the hitch. Well line up the pinholes, insert our pin through our pinholes and secure it and lock it on the other side. We can then turn the black knob at the back of the shank to engage the anti-rattle device. Now with the Kuat NV secured to our Traverse well go ahead and go over a few clearance measurements to see how the two fit together. We have about 16 inches of ground clearance at the rear of the carrier with the platform folded up. more

Watch Video

9/19/2013 8:13:14 AM

Thule Helium Aero Hitch Bike Rack Review - 2012 Chevrolet Camaro- Video

Today on our 2012 Chevrolet Camaro we'll be test fitting the Thule Helium Aero 2 bike carrier for 1-1/4" and 2" hitches, part number 2H9042. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and allow our attached pin to fall into place. We use the hand knob here at the rear of the shank to secure our bike rack to our vehicle and engage our anti-rattle device. Now we'll go over some clearance measurements. We have about 12 1/2" of ground clearance. We've added about 12" to the overall length of our camaro. As you can see, we have full access to the trunk of our car with our bike carrier in its upright position.If you need more room to get into your trunk you can tilt your carrier away from your vehicle by pulling the lever here at the base of the mast. Now we'll pull the level at the top of the mast to swing out our dual arms. more

Watch Video

9/4/2013 11:43:16 AM

Kuat Beta Hitch Bike Rack Review - 2012 Chevrolet Camaro- Video

Today on our 2012 Chevrolet Camaro, well be test fitting the Kuat Beta Folding Two Bike Aluminum Rack for 1-1/4 hitches, part number B202-114. To begin our test fit, well slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and install our pin and lock. At the rear of the shank, well tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now well go over some clearance of measurements. We have about 11-1/2 inches of ground clearance. more

Watch Video

9/4/2013 11:37:25 AM

Yakima DoubleDown Ace Hitch Bike Rack Review - 2009 Chevrolet Traverse- Video

Today on our 2009 Chevrolet Traverse, well be test fitting the Yakima DoubleDown Ace Four Bike Carrier for 1-1/4 and 2 inch hitches, part number Y02451. To begin our test fit, well slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and install the attached pin. Well move to the rear of the shank and tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now well go over a few clearance of measurements. We have about 16-1/2 inches of ground clearance. more

Watch Video

8/28/2013 2:34:27 PM

Yakima DoubleDown Ace 2 Bike Rack Review - 2009 Chevrolet Traverse- Video

Today on our 2009 Chevrolet Traverse, well be test fitting the Yakima DoubleDown Ace Two Bike Carrier for 1-1/4 and 2 inch hitches, part number Y02450. To begin our test fit, well slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and install the attached pin. Well move to the rear of the shank and tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now well go over a few clearance of measurements. We have about 16-1/2 inches of ground clearance. more

Watch Video

8/28/2013 2:32:46 PM

Thule Vertex 4 Hitch Bike Rack Review - 2009 Chevrolet Traverse- Video

Today on our 2009 Chevrolet Traverse we'll be test fitting the Thule Vertex four bike rack 3 1/4 inch and 2 inch hitches, part number TH9029. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pin holes, and thread in our anti-rattle bolt, tightening with a wrench. Now we'll go over a few clearance measurements. We have about 17 1/2 inches of ground clearance. The closest point of the carrier to the rear of the Traverse is about 4 inches. We've added about 11 inches to the overall length of our Traverse. more

Watch Video

8/28/2013 2:32:19 PM

Thule Hitching Post Pro Hitch Bike Rack Review - 2009 Chevrolet Traverse- Video

Today on our 2009 Chevrolet Traverse we'll be test fitting the Thule Hitching Post Pro Folding, Tilting Four Bike Rack with Anti-Sway, part number th934xtr. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and thread in our anti-rattle bolt tightening it with a wrench. Now we'll go over a few clearance measurements. We have about 16 inches of ground clearance. The closest point of the carrier to the rear of our vehicle is about four inches. more

Watch Video

8/28/2013 2:29:53 PM

Thule Doubletrack Hitch Bike Rack Review - 2009 Chevrolet Traverse- Video

Today on our 2009 Chevrolet Traverse, we'll be test fitting the Thule Doubletrack platform-style, two-bike rack. Part number TH990XT. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up our pinhole and thread in our anti-rattle bolt, tightening it with a wrench. Now we'll go over a few clearance measurements. We have about sixteen inches of ground clearance and we've added about nine inches to the overall length of our vehicle. Pull the gray lever to unfold our carrier. With it in this position, we can gain full access to our rear hatch. We'll raise our frame hooks all the way up and undo our wheel straps. We'll grab our bike, place it onto the carrier and secure it first by clamping down our frame hook. more

Watch Video

8/28/2013 2:29:27 PM

Swagman Titan Hitch Bike Rack Review - 2009 Chevrolet Traverse- Video

Today on our 2009 Chevrolet Traverse we'll be test fitting the Swagman Titan Four Bike Carrier for 1-1/4 and 2 Inch Hitches, part number s63410. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and thread in our anti-rattle bolt tightening it with a wrench. Now we'll go over a few clearance measurements. We have about 19-1/2 inches of ground clearance. The closest point of the carrier to the rear of the Traverse is about five inches. more

Watch Video

8/28/2013 2:28:31 PM

Softride Dura Hitch Bike Rack Review - 2009 Chevrolet Traverse- Video

Today on our 2009 Chevrolet Traverse we'll be test fitting the Softride Dura Parallelogram Tilting Four Bike Rack for 1-1/4 and 2 Inch Hitches, part number sr26247. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and thread in our anti-rattle bolt tightening with a wrench and installing the lock. Now we'll go over a few clearance measurements. We have about 16-1/2 inches of ground clearance. The closest point of the carrier to the rear of our Traverse is about three inches. more

Watch Video

8/28/2013 2:28:07 PM

Prorack 4 Hitch Bike Rack Review - 2009 Chevrolet Traverse- Video

Today on our 2009 Chevrolet Traverse, we'll be test fitting the Prorack four-bike carrier for inch and a quarter and two inch hitches. Part number PR8062404. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pinhole and threat in our anti-rattle bolt, tightening it with a wrench and installing the clip on the other side. Now we'll go over a few clearance measurements. We have about sixteen inches of ground clearance. The closest point of the carrier to the rear of our Traverse is about three inches. We've added about twenty-nine inches to the overall length of our vehicle. We'll pull the pin and clip at the base of the carrier and allow it to tilt away from our vehicle. This will give us full access to our rear hatch. more

Watch Video

8/28/2013 2:27:02 PM

Kuat NV Hitch Bike Rack Review - 2009 Chevrolet Traverse- Video

Today on our 2009 Chevrolet Traverse, we'll be test fitting the Kuat NV Aluminum platform style two-bike rack for two inch hitches. Part number N101. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole and install our pin and lock. Here at the rear of the shank, we can tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now we'll go over a few clearance measurements. We have about sixteen and a half inches of ground clearance. The closest point of the carrier to the rear of the vehicle is about a half inch. We've added about twelve inches to the overall length of our Traverse. We can pull the orange lever at the base of the carrier and allow it to unfold. more

Watch Video

8/28/2013 9:08:44 AM

Rhino-Rack 4 Hitch Bike Rack Review - 2009 Chevrolet Traverse- Video

Today, on our 2009 Chevrolet Traverse, we'll be test fitting the Rhino Rack 4 Bike Rack for 2" hitches, part number RVC038. To begin our test fit, we'll slide the shank of the carrier, into the receiver tube of the hitch. Line up the pinhole, and thread in our anti-rattle bolt, tightening them with a wrench and then installing the lock. We'll go over a few clearance measurements. We have about 17" of ground clearance. The closest point of the carrier to the rear of our Traverse is about 2 1/2" away . We've added about 10" to the overall length of our vehicle. more

Watch Video

8/28/2013 4:27:28 AM

Yakima DoubleDown Ace Hitch Bike Rack Review - 2006 Chevrolet Trailblazer- Video

Today on our 2006 Chevrolet Trailblazer we'll be test fitting the Yakima Doubledown Ace Four Bike Carrier, part number y02451. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and install the attached pin. We'll move to the rear of the shank and tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device.Now we'll go over some clearance measurements. We have about 16 inches of ground clearance. The closest point of the carrier to the rear of our Trailblazer is about six inches. more

Watch Video

8/19/2013 4:46:09 PM

Yakima DoubleDown Ace 2 Bike Rack Review - 2006 Chevrolet Trailblazer- Video

Today on our 2006 Chevrolet Trailblazer we'll be test fitting the Yakima Doubledown Ace Two Bike Carrier, part number y02450. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and install the attached pin. We'll move to the rear of the shank and tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device.Now we'll go over a few clearance measurements. We have about 16 inches of ground clearance. The closest point of the carrier to the rear of our Trailblazer is about six and a half inches. more

Watch Video

8/19/2013 4:44:06 PM

Thule Vertex 4 Hitch Bike Rack Review - 2006 Chevrolet Trailblazer- Video

Today on our 2006 Chevrolet Trailblazer we'll be test fitting the Thule Vertex Four Bike Rack, part number th9029. To begin our test fit we'll slide the shank of the carrier into the receiver tube of our hitch. Line up the pin hole and thread in our anti-rattle bolt tightening it with a wrench. Now we'll go over a few clearance measurements. We have about 17-1/2 inches of ground clearance.The closest point of the carrier to the rear of our vehicle is about three and a half inches. We've added about 13 inches to the overall length of our Trailblazer. more

Watch Video

8/19/2013 4:42:35 PM

Thule Hitching Post Pro Hitch Bike Rack Review - 2006 Chevrolet Trailblazer- Video

Today on our 2006 Chevrolet Trailblazer we'll be test fitting the Thule Hitching Post Pro Folding, Tilting Four Bike Rack, part number th934xtr. To begin our test fit we'll slide the shank of the carrier into the receiver tube of our hitch. Line up the pin hole and thread in our anti-rattle bolt tightening it with a wrench.Now we'll go over a few clearance measurements. We have about 16 inches of ground clearance. The closest point of the carrier to the rear of our Trailblazer is about seven and a half inches. We've added about 17 inches to the overall length of our vehicle. more

Watch Video

8/19/2013 4:40:36 PM

  16     17     18