Trailer Wiring Harness Installation - 2006 Toyota Sienna Video

Products Featured in this Video

How to Install a Trailer Wiring Harness on a 2006 Toyota Sienna

Today on this 2006 Toyota Sienna were going to install part number 118304 from Tow Ready. To start our install well open up the back hatch and then well go ahead and remove both taillights. Well also remove the vehicles rear threshold and then well also have to loosen up the side panels as well to get access to the wiring. On the passengers side well have to get through the jack storage… see more >

Info for this part was:

Test Fit:

Joe V

Test Fit:

Nicholas E

Test Fit:

Randy B

Video Edited:

Zack K

Video Edited:

Jacob T

Video Edited:

Sue W

Video by:

Joshua S

Video by:

Kathleen M

Installed by:

Cole B

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.

Explore Expert Info

Most Popular

Videos

Help Articles

Expert Answers

Best 2006 Toyota Sienna Trailer Wiring Options

etrailer.com Trailer Hitch Installation - 2006 Toyota Sienna

Trailer Hitch Installation - 2006 Toyota Sienna - Draw-Tite

Best 2006 Toyota Sienna Trailer Hitch Options

Trailer Hitch Installation - 2006 Toyota Sienna - Curt

Trailer Wiring Harness Installation - 2009 Toyota Sienna

Brophy Mounting Bracket for 4-Pole Flat Trailer Connector Review

Draw-Tite QSP Trailer Hitch Silencer and Cover Review

Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C55580 Review

Air Lift Air Helper Springs Installation - 2005 Toyota Sienna

Reese ATV Hitch - Hitch Only - RP7065000 Review

Best 2007 Toyota Sienna Trailer Wiring Options

Trailer Wiring Diagrams

How to Choose a Hitch-Mounted Bike Rack

How to Choose a Bike Rack for a Sedan or Hatchback

Brake Controller 7- and 4-Way Installation Kit (ETBC7)

Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)

How to Measure for Trailer Hitch Drop

Routing the Power Wire for a Trailer Wiring Harness

What Size Bolts are Needed to Install Curt Hitch in a 2006 Toyota Sienna

The Curt trailer hitch part #C13105 comes with all of the install hardware needed, but the bolts are size M12-1.25x40 hex. If you need the replacement hardware you would want part #RHK. If you enter the part number on this product page we will ship…

view full answer...

Will Trailer Wiring Harness from 2004 Toyota Sienna Fit a 2009 Toyota Sienna

There isn't any modification needed to wiring harness #C55580 because it fits both the 2004 and 2009 Toyota Sienna as-is. I have included a link to a video showing an example installation on a 2009 Sienna for you.

view full answer...

I recommend the Kuat Piston Pro X Bike Rack for 4 Bikes #KU45VR for you. This rack is capable of carrying 4 bikes with wheel sizes from 18" to 29" diameters. The Carrier itself is one of the easiest we have to use and load your bikes as it…

view full answer...

Do You Have to Have 4-Way to Use Kuat Piston Pro X Bike Rack

Good question, and it is not a necessity for your car to have a 4-way flat trailer connector in order to use the Kuat Piston Pro X bike racks. The 4-way connector that plugs in between the bike rack and the 4-way on your car (if you had one) comes…

view full answer...

Does Trigger Wire for Rear View Safety Backup Camera System Have to be Reverse Light

Since you can use basically any trigger circuit for the Rear View Safety Backup Camera system part #RVS-772718 you would not have to use the reverse light circuit and you could run it to a circuit that comes on with the ignition so that it is active…

view full answer...

Torque Specs for Trailer Hitch On 2017 Toyota Sienna

The correct etrailer Trailer Hitch Receiver for a 2017 Toyota Sienna is part #e98837. This hitch uses M12 - 1.25 x 40 hex bolts. The torque spec for these bolts can be found in the installation instructions below. It's important to go off of the…

view full answer...

Parts Needed to Add a 7-Way Trailer Connector to a 2006 Toyota Sienna

For the 2006 Toyota Sienna you would need to use the 4 and 7 way installation kit #ETBC7. There is no powered plug in connector available for the Sienna just because the vehicle is not set up for it. If you already have a 4-Way wiring harness on the…

view full answer...

Installation Instructions for etrailer Trailer Hitch Receiver for 2019 Toyota Sienna

We do have the instructions available for the etrailer Trailer Hitch Receiver #e98837 that fits your 2019 Toyota Sienna. I have added a link below to the installation instructions for you, as well as attached a copy for you here. I have also added a…

view full answer...

Tap Size One Size Bigger than M12 - 1.25 for Hitch Install with Stripped Nut

I would retap the threads with the next size up. Which from my research would be M12-1.5. If you are still unsure you can take the bolt you have with you to a hardware store, tell them you are in need of a tap that is the next size up, and they will…

view full answer...

Parts Needed to Install a 7-way Adapter on a 2022 Toyota Sienna

The first thing you will need to get a 7-way on your 2022 Toyota Sienna is to wire a 4-way adapter like the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #TK69FR. There is no plug in play 7-way for your vehicle, you have to first…

view full answer...

Will Installing a Trailer Hitch Receiver Void the Warranty on a 2017 Toyota Sienna

According to the Magnusson-Moss Warranty Act, unless a modification that you added to your vehicle actually causes the problem, your dealer must honor the warranty. We do have some trailer hitch receiver options that are confirmed to fit your 2017…

view full answer...