Brake Controller Recommendation and How To Install it in a 2003 Chrysler Town and Country
Question:
Trailer Brake Controller I have a 2003 Chrysler Town and Country with the factory Trailer Tow Package. The hitch and 4 wire harness on a 7 pole connector were installed by a hitch company.I want to put electric trailer controler on it. I am looking at a Draw Tite controler . What else will I need to intsall it on my Van? Thank You
asked by: Dave A
Helpful Expert Reply:
First let's start with a brake controller. For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that will apply the trailer brakes at the same intensity as the tow vehicle brakes are applied. Unlike a time-delayed controller like the # 5504 that you referenced that always will apply the brakes at the same intensity regardless of the braking situation.
Next, for a wiring kit to install the brake controller and the 7-way adapter you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that has voltage when the brakes are applied and none when not applied. This will be the circuit you will run the red wire to on the brake controller
Finally you will need to run a length of 10 gauge wire (part # 10-1-1) from the brake output circuit of the controller to the brake output circuit of the 7-way you have on your vehicle. The # 10-1-1 is sold by the foot so you will need to order a quantity of the amount of feet you will need.
I attached an FAQ on installing brake controllers for you to check out.
Products Referenced in This Question
Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Brake Controller Recommendation for a Truck with Air Brakes and a Trailer with Electric Brakes
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: How do I Tell if the Brake Controller is Bad
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Q&A: Should I Get a Proportional or Time-Delayed Brake Controller
- Q&A: Recommended U-Bolts And Plate For A 1-1/2" Wide Square Axle
- Q&A: Brake Controller Plug Location for 2020 Chevy Silverado 1500