Ground Clearance for the Curt Hitch C26VV

Question

Question:

What is the ground clearance below the 2inch receiver after installing of the hitch on the Grand Highlander

asked by: Chris

0

Hitch Measurement
(click to enlarge)

Expert Reply:

Sorry Chris but we do not have that information yet and Curt doesn't take those measurements. We haven't had the chance to install the Curt Hitch item # C26VV on a 2024 Toyota Grand Highlander yet so we haven't had the opportunity to take any measurements.

expert reply by: Jerred H

0

Answer 1

Hey Micah, I confirmed with Curt that the Curt Trailer Hitch Receiver #C26VV would be a fit for your 2024 Toyota Grand Highlander with dual exhaust. If you plan on towing a trailer then you'll want to pick up the Curt T-Connector Vehicle Wiring…

view full answer...

Answer 2

We can definitely help install a brake controller and 7-way on your 2024 Toyota Grand Highlander but first the brake controller I recommend is the Redarc Tow Pro Liberty part #RED24FR with the install harness part #RED69FR. As this controller puts…

view full answer...

Answer 3

To install a 7-Way harness on your 2024 Toyota Grand Highlander you will need two separate wiring harnesses because they don't make just one that'll do the job. The first harness you'll need is either the Curt T-One Vehicle Wiring Harness…

view full answer...

Answer 4

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Ground Clearance for the Curt Hitch C26VV

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching