Parts Needed to Power Electric Brakes on Triple Towed Motorcycle Trailer
Question:
Hi,I do tow a fifth wheel trailer with a 2019 Ram 3500 dually and I will add second motorcycle trailer in the back_ double towing- it have electric breakes. The fifth wheel have a flat 4 pin hardwired to it from factory .The question is: Do the fifth wheel have to be rewire for the 7 pin or I can purchase an adapter,_ 4 to 7 pin_ and I do have to run a second electric breakes controller for the second trailer? Thank you for your help.
asked by: Claudio M
Expert Reply:
You will need a little more than just the adapter but that is off to a good start. The Curt Trailer Connector Adapter # C57672 will connect to the 5th wheel 4-way so the signal power will carry over to the 7-way connector. However, you will still need to run wire to connect to the brake output circuit.
Voltage drop is a definitely a concern so I recommend replacing the brake output wire on your entire setup with 6 gauge wire. So you will be replacing it starting at the brake controller and running it to the 5th wheel brakes then back to your 7-way on the 5th wheel.
As long as your brake controller can handle the number of axles you have it should be fine. For example, the # 90195 you looked at is compatible with up to 4 axles. I'm guessing your motorcycle trailer has 1 axle so even if you have a triple axle 5th wheel you're good.
If you don't want to replace all of the wiring another option is to switch to surge brakes. Surge brakes are popular with this kind of setup I also recommend checking local laws for the areas you will be driving through since this is not legal in all states.
Products Referenced in This Question
Curt Trailer Connector Adapter - 4-Way to 7-Way RV and 4-Way Flat
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- CURT
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Trailer Wiring Diagrams
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Installing an Electric Brake Controller on 2007-2013 GM Full-Size Truck or 2007-Present GM SUV
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Does the Tekonsha P3 Trailer Brake Controller Turn Off or Stay On All the Time
- Q&A: Parts Needed To Install A Brake Controller On A 2023 Freightliner Cascadia
- Q&A: Suspension Enhancement Recommendation for 2019 Toyota RAV4
- Q&A: How Does Brake Controller Install on Freightliner S2RV Chassis
- Q&A: Parts Needed to Add 7-Way & Brake Controller on 2023 Kia Sportage
- Q&A: Wiring Configuration for Tekonsha Prodigy P3 Trailer Brake Controller 90195
Claudio
3/19/2024
Robin H : thank you for your help with this issue, I was thinking,the fifth wheel plugs in the bed of the truck, my 2019 Ram 3500 also have a 7 pin plug in the bumper, so what about if I use a 7 pin extension from the bumper of the truck ,router underneath of the fifth wheel to the back of it so I can plug the motorcycle trailer.The fifth wheel have 2 axels with brakes and the motorcycle trailer have one axle with electric breake. Total of 3 axles with electric breakes,I believe that the OEM controller in the truck can handle 3 breaks. What do you think? If that's the case, you guys have a 35/37 feet 7 pin cord extension? Again, thanks for all your help.