What Kind Of Fittings Are On The Roadmaster Metric-to-Standard Brake Line Tee RM-7923

Question

Question:

hi the Item # RM-7923 can you tell me pictures are not real clear the one end has a male 10mm bubble flare, is the other end 10mm female bubble flare? and is the side port 1/8 NPT? thank you

asked by: Rod N

0

Expert Reply:

The threads on the ends of the Roadmaster Metric-to-Standard Brake Line Tee # RM-7923 are 10mm male and 10mm female. The female thread that exits from the side of the Tee is a 3/16" flared NPT.

expert reply by: Jesse M

0

Answer 1

If your motorhome brake line has metric fittings, it will be necessary to use a metric-to-standard T-fitting to attach the proportioning valve. This fitting is not supplied in the RoadMaster BrakeMaster Second RV Kit for Hydraulic Brakes #RM-98300.…

view full answer...

Answer 2

The Roadmaster Metric-to-Standard Brake Line Tee #RM-7923 has an overall length of 2-1/8". The threads on the ends of the Tee are 10mm male and female. The female thread that exits from the side of the Tee is a 3/16" flared NPT.

view full answer...

Answer 3

The fittings that are included with the Conversion Regulator Kit for #RM-9060, part #RM-900001, includes standard fittings but not metric fittings or adapters. You would need #RM7921.

view full answer...

Answer 4

Since you are going from the BrakeMaster system #RM-9160 for a motor home with air brakes to a motor home with hydraulic brakes, kit #RM-98300 will be the kit that you need.

view full answer...

Answer 5

If the previous owner was using a Roadmaster Brakemaster system, #RM-9100 or #RM-9160 then there are several parts you will need to get it to work with an RV that uses hydraulic brakes. Basically you will need the second RV kit #RM-98300. There is…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

What Kind Of Fittings Are On The Roadmaster Metric-to-Standard Brake Line Tee RM-7923

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching