Replacement Switch for a RAM Tongue Jack on a 2020 Forest River Vibe TT

Question

Question:

We are looking for a replacement switch for our tongue jack. We have a 2020 Forest River Vibe 18RB with a RAM tongue jack.

asked by: Amy

0

Expert Reply:

For your RAM tongue jack, you can use the Replacement Power Switch for RAM Electric Trailer Jack with Footplate # EJ-3520-PSW.

expert reply by: Bryce D

0

Answer 1

If you check out the picture I attached you can see how the wires of the Ram jack switch #EJ-3520-PSW are supposed to be ran to it.

view full answer...

Answer 2

The Electric A-Frame Tongue Jack, #JET-3555, runs off a 12 volt battery. The best source for power would be from a 12 volt battery (like a car battery) mounted on the trailer. The red power wire on the Electric A-Frame Tongue Jack, #JET-3500, is the…

view full answer...

Answer 3

We went ahead and looked up the information regarding your Kedu HY60D switch. For a compatible switch that will work, I recommend the Mini Momentary Switch - On/Off/On - DPDT #37213445. This particular switch has a cutout dimension of 0.745 inch tall…

view full answer...

Answer 4

I attached a picture that I got from RAM jacks that shows how the RAM Jack switch part #EJ-3520-PSW that you referenced gets wired up.

view full answer...

Answer 5

I have attached a photo you can use to connect the Replacement Power Switch #EJ-3520-PSW to your 3,500 lb RAM jack. We don't have a direct wiring diagram but if you notice even though the wires are the same colors they look pretty different so…

view full answer...

Answer 6

If all the wiring on your electric jack is in good condition, and there doesn't seem to be a ground issue, it is likely you simply need to replace the switch itself. For your Ram 3500 Series Jack, the correct replacement switch is part…

view full answer...

Answer 7

For a Ram 3,500 lb jack we have the replacement Light Switch #EJ-3520-LSW and Power Switch #EJ-3520-PSW. If you remove the cover you should be able to then pop the switches out of the head to replace them. There should also be the blade-style wiring…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Replacement Switch for a RAM Tongue Jack on a 2020 Forest River Vibe TT

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching