Will Westin E-Series Round Nerf Bars Work on a 1995 Ford Bronco with Side Exhaust

Question

Question:

I have a 1995 Ford Bronco Eddie Bauer that has nerf bars already, but these are 51inch long and will interfere with installing side exhaust tail pipes in front of the rear wheel much like the Mercedes G Wagon. Do you happen to have a 48inch stainless steel bar that will fit my truck and that can be lowered to 4inch below the edge of rocker panel? Tks

asked by: Louis M

0

Expert Reply:

I might have an option for you but we don't have custom kits for your vehicle with aftermarket modifications. The nerf bars are all going to be designed for models with factory exhaust therefore there is nothing under the rocker panel to interfere. In order to make any of our steps work you'd need to make modifications i.e. trimming the bars and or possibly modifying the brackets. The Westin E-Series Round Nerf Bars part # 23-0530 might be our best option, I have attached a photo that shows where they install as well as a photo of them installed on a Bronco. They look like they might clear the exhaust but we can't confirm this. I don't have any measurements to provide either unfortunately, it will be really be up to you to determine fit as this is a custom application.

expert reply by: Conner L

0

Will Westin E-Series Round Nerf Bars Work on a 1995 Ford Bronco with Side Exhaust
(click to enlarge)

Answer 1

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 2

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 5

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 6

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Will Westin E-Series Round Nerf Bars Work on a 1995 Ford Bronco with Side Exhaust

Product Page this Question was Asked From

Continue Researching