Steps For Replacing Bevel Gears In HappiJac Jacks
Question:
CWhere are the pictures showing steps for replacing Bevel gear set #182851 into happy jacks. 4600R
asked by: Richard R
Expert Reply:
The Replacement Bevel Gears for HappiJac Truck Camper Jack Systems # LC182851 are the correct gears for your 4600 jacks. However, we unfortunately do not have any pictures or videos of the steps to replace the gears. I will go over how to do this the best I can below.
First remove your motor using the two bolts (if you have a motor on your jack). Then take a flathead screwdriver to the top of the jack to pry out the cam lever and hinge the button from the sides of the motor cam. Grab the loose part with needle nose pliers.
Use the screwdriver again to pop off the e-ring clip from the end of the docket shaft and pull the crank socket from the tube along with the vertical bevel gear. After this you can grab the horizontal bevel gear too. Then take the drift pin from the drive shaft. You can completely remove the outer tube off of the inner tube. Remove the washer and nylon bushing from the outer tube. Now, you're ready to install the new gears.
Now, you're ready to install the new gears. Which is basically the same steps, but in reverse order.
Product Page this Question was Asked From
Replacement Bevel Gears for HappiJac Truck Camper Jack Systems
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Gears
- Lippert
more information >
Continue Researching
- Shop: Replacement Bevel Gears for HappiJac Truck Camper Jack Systems
- Shop: Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
- Shop: Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 4,500 lbs - Black
- Shop: HappiJac Manual Truck Camper Jack System - 36-1/2" Lift - 11,200 lbs
- Shop: Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black
- Shop: Stromberg Carlson Electric A-Frame Tongue Jack - 18" Lift - 2,500 lbs
- Search Results: ac shroud
- Search Results: bargman
- Shop: Replacement Clutchless Motor Head for HappiJac Truck Camper Jacks - Qty 1
- Q&A: Replacement Bevel Gear Set for Happijac Square Tube Jack
- Q&A: Bevel Gear Replacement For Happijac Truck Camper Jack System # LC736514 # LC736515
- Video: Review of Lippert Components - Trailer Jack,Camper Jack - LC362485
- Video: Review of Lippert HappiJac Electric Jack Replacement Junction Boxes - LC69UD
- Search Results: lc362485
- Q&A: Solution for Damaged Front Jack Leg of Lippert Ground Control 3.0 Leveling System
- Shop: Brake Controller
- Q&A: Replacement Control Board for HappiJac Jack System with Corded Controller
- Search Results: license plate lights
- Q&A: Recommended Replacement for Atwood GC10A-4E RV Water Heater
- Q&A: Can Furrion Tankless Water Heater Replace Atwood AT94022
- Q&A: Direct Replacement Water Heater for Atwood Model GC10A-4E
- Search Results: bargman led
- Video: Review of Lippert Components Camper Jack Parts - Replacement Cap Kit - LC183332
- Shop: Roof Rack
- Video: Review of HappiJac Camper Replacement Parts - Truck Camper Jack Parts - LC182491
- Video: Review of HappiJac Camper Jacks Extender Bracket - HJ54FR
- Shop: Base Plate for Tow Bar
- Video: Review of HappiJac Manual-to-Electric Truck Camper Jacks Conversion Kit - LC733960-182524
- Video: Review of HappiJac Trailer Jack - Camper Jack - LC736515
- Search Results: lc733960~182524