Will Existing Break Away Kit Work When Converting Electric Brakes To Hydraulic Disc Brakes
Question:
I am installing the above unit as part of a conversion from electric magnetic to hydraulic disc. I have an existing break away switch, and its wired directly to the two deep cycle trailer/house batteries. They, in turn, are charged while driving from the tow vehicle. I see the Dexter break away kit comes with its own battery, etc. Do I really need this for the break away switch to work properly with a hydraulic actuator or will my existing switch, properly wired and with batteries properly charged, work correctly? Thanks.
asked by: Mark F
Expert Reply:
The break away kit you have on your trailer should be fine if you have at least 9 amp/hour on your system, as this is what is required by the Dexter Brake Actuator, part # K71-651. It sounds as though you should be okay with two batteries hooked to your system now. If you are using the trailer connector for your batteries, they will only have the charge maintained, and will not increase the charge of the batteries. I have attached a link to our product page for battery chargers.
If your system does not meet the required power level, I recommend the Dexter Breakaway Kit, part # 34-285.
Products Referenced in This Question
Dexter Trailer Breakaway Kit with Built-In Battery Charger - Top Load
- Trailer Breakaway Kit
- Kit with Charger
- Top Load
- Single-axle
- Tandem-axle
- Dexter
more information >
Product Page this Question was Asked From
Dexter DX Series Electric Over Hydraulic Brake Actuator for Disc Brakes - 1,600 psi
- Brake Actuator
- Electric-Hydraulic Brake Actuator
- Marine
- Travel Trailer
- Disc Brakes
- Dexter
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Review of Titan Brake Actuator - Replacement Master Cylinder for Disc Brakes - T4747100
- Video: Titan Brake Actuator - Surge Brake Actuator - T4750800 Review
- Video: Titan Brake Actuator - Surge Brake Actuator - T4750720 Review
- Video: Titan Brake Actuator T1242600 Review
- Q&A: Troubleshooting Master Cylinder T4749501042 Not Releasing Fluid When Installed on My Trailer
- Q&A: How to Replace the Shock on a Titan Model 10 Surge Brake Actuator
- Q&A: How to Tell Difference Between Titan Model 20 Drum and Disc Actuator
- Q&A: Common Replacement Parts for Model 10 Brake Actuators
- Shop: Dexter Zinc-Plated Brake Actuator - Disc - 2-5/16" Ball - Bolt On - 12,500 lbs
- Shop: Solenoid Valve Replacement Kit for Dexter Brake Actuators with Reverse Lockouts
- Shop: Dexter Zinc-Plated Brake Actuator w/ Drop - Disc - 2-5/16" Ball - Bolt On - 20,000 lbs
- Shop: Replacement Master Cylinder Assembly for Dexter Model 10 and Model 20 Brake Actuators - Drum
- Shop: Replacement Inner Slide for Dexter Model 20 Brake Actuator with Drop and 2-5/16" Ball
- Shop: Replacement Master Cylinder Assembly for Dexter Model 10 and Model 20 Brake Actuators - Disc
- Shop: Dexter Hydraulic Brake Actuator w/ Drop and Electric Lockout - Disc - Zinc - 2-5/16" Ball - 20K
- Q&A: How to Determine if Trailer has 84 Spindle to Pick Out Replacement
- Search Results: trailer brakes
- Article: Trailer Wiring Diagrams
- Shop: Brake Controller
- Search Results: trailer brake controller
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 10~51
- Shop: Trailer Wiring
- Search Results: l68149
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Shop: Towing Mirrors
- Article: Determining Trailer Tongue Weight
- Shop: Base Plate for Tow Bar