Inside Dimensions of TorkLift HiddenPower Under-Vehicle Battery Box TLA7727

Question

Question:

Will this battery box fit a Renogy Deep Cycle AGM 12 Volt 100Ah Battery 13.1 x 6.9 x 8.6 inches

asked by: SHELLY M

0

Expert Reply:

Yes it will! The reason for that is the inside dimensions are 14-1/2 inches long x 7-7/8 inches wide x 9-3/4 inches tall for the TorkLift HiddenPower Under-Vehicle Battery Mount with Battery Box # TLA7727.

expert reply by: Kyle S

0

Answer 1

Typically two batteries are needed for a 2,000 watt inverter like the part #34278156 that you referenced.

view full answer...

Answer 2

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 3

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

Blue Ox has base plate kits that fit your 2023 GMC Yukon XL with the part #BLU54VR which fits the AT4 models with 4L and the part #BLU58FR which fits the non-AT4 models. While we haven't had the chance to shoot an install video for either of…

view full answer...

Answer 8

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 9

Please note the attached instructions. The Lippert Anti-Billowing Kit for Solera Slide Topper Awnings, #LC78FR should be installed on the end of the awning that is closest to the front of the unit. 1. Make sure awning is fully retracted. 2. Place the…

view full answer...

Answer 10

If you check out the picture I attached you can see that the roller and slide out awning assembly of the Solera RV Slide-Out Awning #LCV000435661 actually will sit below the awning rail so your setup having a tight clearance between the rail and the…

view full answer...

Answer 11

I recommend to use the Solera 16-1/2' Slider part #LCV000435661 which matches the boxes width exactly so you will not have side overhang like we normally recommend but it is the biggest slide topper available to fit the 198" width of your…

view full answer...

Answer 12

I advise measuring the two spindles that you have and making sure that the parts that you are wanting to interchange will be a compatible fit. I have included a photo that shows where where to take these measurements on your exiting spindles. These…

view full answer...

Inside Dimensions of TorkLift HiddenPower Under-Vehicle Battery Box TLA7727

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching