Mounting Dimensions for Slipper Leaf Spring e74SR and Tandem Hanger Kit APT6SE
Question:
On the diagram for tandem 7k axles and the 26 5/8” slipper springs is it all correct as it is. With spring open ends facing towards the front of the trailer. So a person could use all this information and measurements shown to assemble ?
asked by: John E
Helpful Expert Reply:
With the 26-5/8 inch long leaf spring part # e74SR you referenced and the hanger kit part # APT6SE you also mentioned the dimensions in the chart you referenced would be correct to use. The distance between the front and center hanger should be 28-1/2 inches, distance between center and rear hanger 29-1/2 inches, and the distance between axle centers 33 inches. This will then put the distance from the trailer frame to the axle center right at 4-1/2 inches.
Products Referenced in This Question
5-Leaf Slipper Spring w/ Hook End for 7,000-lb Trailer Axles - 26-5/8" Long
- Trailer Leaf Springs
- Slipper Springs
- Hook End
- 7000 lbs
- 2 Inch Wide
- 5 Leaf
- 26-5/8 Inch Long
- Painted
- etrailer
more information >
Product Page this Question was Asked From
Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 12" Long Equalizers
- Trailer Leaf Spring Suspension
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Slipper Springs - 2 Inch
- Tandem Axle
- etrailer
more information >
Continue Researching
- Article: Slipper Spring Trailer Suspension System Review
- Shop: Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 12" Long Equalizers
- Shop: Equalizer for 2" Wide Slipper Springs - 12" Long - 7/8" Center Hole
- Shop: 5-Leaf Slipper Spring w/ Hook End for 6,000-lb Trailer Axles - 27" Long
- Shop: Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 13-1/8" Long Equalizers
- Search Results: sp~160275
- Search Results: e67sr
- Search Results: sp~285275
- Q&A: Recommended 8,000 lb Slipper Spring Hanger and Equalizer Kit for 2 Inch Springs
- Article: Double-Eye Trailer Suspension System Review
- Search Results: sp~232275
- Q&A: Slipper Spring Hanger Positioning for 7,000 lb Tandem Axle
- Search Results: e74sr
- Search Results: sp~230275
- Q&A: Torque Spec for Replacement U-Bolt with Nuts 175211
- Search Results: sp~161275
- Shop: Tandem-Axle Trailer Equalizer Kit for 2" Slipper Springs - 13-1/8" Long Equalizers
- Shop: 4-Leaf Slipper Spring w/ Hook End for 4,000-lb Trailer Axles - 26-5/8" Long
- Q&A: How to Determine Axle Spacing on a 5,000 lb Tandem Axle Trailer
- Q&A: How to Determine Hanger Spacing on 5,200 lb Tandem Axle Trailer
- Q&A: Tandem Axle Hanger Kit for 2 inch Wide Slipper Springs
- Video: Redline Trailer Suspension SP01-160 Review
- Shop: Replacement U-Bolt with Nuts for 2" Wide, Square Trailer Axles - 9/16" Diameter
- Q&A: What is the Hanger Spacing on the 6-Leaf Slipper Spring # e46SR?
- Article: Where to Position the Trailer Axle?
- Shop: Tool Box
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: How to Raise Your Travel Trailer Height
- Video: etrailer Trailer Suspension - Leaf Spring Suspension - APT6SE Review