Recommended Hand Winch for 70 Pound Kayak

Question

Question:

I need a simple hand crank winch that can pull a 70# kayak up a dock stairs ladder thats apx 9foot long. I just need to get the kayak to the top of the flat part of the deck. So from the beach whete I would hook it up, Id need apx 20foot of thin cable or rope that can handle 70#.

asked by: Dean

0

Expert Reply:

For your 70 lb kayak you could use the Buyers Products Trailer Hand Winch - 800 lbs # 337HW800S. This has an 800 lb capacity and comes with a 26' long nylon strap.

expert reply by: Robin H

0

Rock Measurements.
(click to enlarge)

Answer 1

To mount the CE Smith Winch Stand #CE31013G on a trailer requires you to slip the lower portion with the holes drilled through it over the pole tongue of your trailer. The various holes are there to allow you to match the correct height and angle…

view full answer...

Answer 2

The CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide #CE31013G should work on the center beam based on the measurements you gave. The additional height of the center beam won't be an issue as the width is still 2 inches.…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Recommended Hand Winch for 70 Pound Kayak

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching