Hardware Kit for Westin HDX Grille Guard to Fit 2017 Ford F-250 Super Duty

Question

Question:

Do you sell a hardware replacement kit for the Westin hdx grill gaurd to fit a 2017 f250 I can’t seem to find it here thanks

asked by: Dustin

0

Expert Reply:

Since the Westin HDX grille guard part number that fits your 2017 Ford F-250 is the part # 57-3905 the correct hardware kit you'd need is the # 57-3905PK.

expert reply by: Jameson C

0

Answer 1

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine,…

view full answer...

Answer 2

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs…

view full answer...

Answer 3

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 4

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

It sounds like you are on the right track for tracking down where the issue is. That said, the integrated brake controllers they were putting in trucks around 2008 weren't as reliable as the ones they've been installing since then. Especially…

view full answer...

Answer 12

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Hardware Kit for Westin HDX Grille Guard to Fit 2017 Ford F-250 Super Duty

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching