What is Thickness of LaSalle Bristol XTRM Roof Membrane

Question

Question:

I need a 25foot x 9foot roof for my camper, how many mils is your product? I see comparable pvc kits butyl tape, adhesive, leveling compound, etc included with their pvc membranes for a similar price. your isnt a kit is it? fyi, I just bought 4 hubs for my dump trailer from you guys, the purchase went well, thanks for that!

asked by: Dan P

0

Expert Reply:

The LaSalle Bristol XTRM roof membrane like part # 344270341415, is 27 MIL which makes it about 0.68 mm thick. This is not a kit and is just the membrane. For the rest of the components to install the membrane you'd need the part # AL63FJ and you'd be set. This includes adhesive, self leveling sealant, non sag sealant, and butyl tape.

expert reply by: Jameson C

0

Answer 1

The LaSalle Bristol XTRM roof membrane like part #344270341415, is 27 MIL which makes it about 0.68 mm thick.

view full answer...

Answer 2

The Alpha Systems Superflex TPO RV Roof Membrane #AL25CV is 0.30" thick. This is the only thickness they offer currently for the TPO. You will need the Alpha Systems RV Roof Replacement Installation Kit #AL63FJ to install this roof…

view full answer...

Answer 3

To add the Alpha Systems RV Roof Replacement Installation Kit for Roofs up to 25' - White #AL63FJ you won't need to remove all of the adhesive, you can apply the new adhesive over the old and it will work. If there are major spots…

view full answer...

Answer 4

The LaSalle Bristol XTRM EXP 90 Adhesive for RV Roofs #344270341415 must be applied to a clean and porous surface. So you will not be able to apply the adhesive to itself. You must either sand the surface clean or apply the new roof sheathing.

view full answer...

Answer 5

The height of the exterior portion of the Ventline Vanair 12-Volt Trailer Roof Vent #VP-543SP that you referenced is 2-5/16 inches.

view full answer...

Answer 6

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of…

view full answer...

Answer 7

Typically leaf springs will stretch around 1/4 of an inch or so when they are worn out but if the springs are 30 years old I could see it easily being 3/4 inch instead. So based on yours currently being 26 inches long and 30 years old your best…

view full answer...

Answer 8

To replace your defective Power Gear 130-1305 RV Slide-Out motor, you'd use the LCI #LC368446 as confirmed by Lippert. The LCI #LC386322 motor you referenced replaces a different Power Gear motor, the 13-1127, so it's not the one…

view full answer...

Answer 9

That is not a fun thing to walk into when opening up your camper for the season! Based on the damage shown in the picture you attached I recommend simply replacing the affected ceiling inside the camper with a whole new section of material. Then to…

view full answer...

Answer 10

I checked with my roof installer, and got a hold of a sample of the LaSalle Bristol #3441700534142711435 myself, and found out that either side can be glued down. There is no up or down. Both sides are identical. This membrane is glued down with…

view full answer...

Answer 11

The installation of the Landing Gear Set part #RVLG-8000 will be fairly straight forward. Basically, you will need to have a metal support structure so you can attach welded tabs part #LC113511 to it, 15-1/2" apart. Once these are installed you…

view full answer...

Answer 12

Yes, I attached a diagram you can use to install the #LC146059 that you referenced.

view full answer...

What is Thickness of LaSalle Bristol XTRM Roof Membrane

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching