Recommended Axle Replacement On A Carry-om 6x12 Utility Trailer
Question:
I have a Carry-on 6x12 utility trailer that needs a replacement axle with hubs. The original axle is a Carry-On 3K8874 Dexter # 51955 with a GAWR of 3500 lb. The Hub Face dimension is 88.0 inches, the Spring Centerline dimension is 74.50 inches, and the springs are under-slung. The hub bolt pattern is 5 on a 4.5 inch circle, and there are no brakes. My question.....is your listed Dexter 35545I-ST-89 Axle with Idler Hubs a direct replacement? The axle dimensions shown are slightly different than those on my trailers original axle. I have attached pictures for reference.
asked by: Daniel O
Expert Reply:
When it comes to The Dexter Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 89 inch Long - 3,500 pounds # 35545I-ST-89 it is not a direct replacement but it will work for your Carry-On 6x12 utility trailer.
This axle has a underslung design- spring seats are welded to underside of axle for mounting leaf springs. The bearings, races, seals, grease caps, wheel studs, lug nuts, and marine-grade wheel bearing grease are included. The hub face to hub face is 1 inch longer then your original axle so that is a 1/2 inch on each side, and the spring center to spring center is 74 inches which means your axle is 1/2 inch longer. You will have to move the spring seat over a little bit. There will be no problem with changing over to the # 35545I-ST-89 axle.
I attached a review video link below.
Product Page this Question was Asked From
Dexter Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Trailer Axles
- Leaf Spring Suspension
- Standard Spindles
- Idler Hubs
- 3500 lbs
- 5 on 4-1/2 Inch
- 74 Inch Long
- 89 Inch Long
- No Drop or Lift
- Dexter
more information >
Continue Researching
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Search Results: trailer wheel hubs
- Video: etrailer Trailer Idler Hub Assembly Installation
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-545-35-G-EZ-K Review
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Article: Trailer Tire Sizing
- Shop: 3-Leaf Double-Eye Spring for 2,000-lb Trailer Axles - 20-3/8" Long
- Shop: Dexter Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 38" Axle Spacing
- Search Results: 3500 spindle
- Shop: 3-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 23-1/8" Long
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Pre-Greased
- Q&A: How to Determine Axle Capacity on a 12 Foot Tandem Axle Utility Trailer
- Search Results: spindle
- Search Results: spindle kit
- Search Results: hub and spindle
- Search Results: trailer hub
- Q&A: What are Overall Dimensions of Typical Trailer Axle
- Search Results: spindle hub
- Q&A: Constructing an Axle from Pipe and Spindle for Use on Homemade Trailer
- Q&A: How to Determine Axle Placement for a Tandem Axle Trailer
- Q&A: Information Needed To Specify Replacement Trailer Axle for 6x12 Enclosed Trailer
- Q&A: How to Pick Out Trailer Axle with 8 Lug Bolt Pattern
- Video: Review of etrailer by AxleTek Trailer Axles - 3,500 lbs Trailer Axle with Idler Hubs - e97YR
- Q&A: Recommendation to Replace Trailer Axle with 70" Spring Center and 85-1/2" Hub Face Length