Can I Use Shorter HD Crossbars On My Yakima OverHaul HD For My 2015 Toyota Tacoma

Question

Question:

Im looking for this setup but I want 55inch cross bars, 60inch max, can you substitute them in?

asked by: Aaron

1

Helpful Expert Reply:

Your 2015 Toyota Tacoma's truckbed has two vehicle styles, one with a Deck Rail System and one without. There are two different Yakima ladder racks that are compatible, one for each truck bed option. They are as follows.

If your truck has the Deck Rail System, the ladder rack that is compatible is the Yakima OverHaul HD Truck Bed Ladder Rack for Toyota/Nissan Utility Tracks - 500 lbs - 68" Bars, part # Y01151-5868.

If you do not have the Deck Rail System on your Tacoma, your ladder rack is the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack - Aluminum - 500 lbs - 68" Crossbars, part # Y01151-58.

Each of these ladder racks come with 68" long Yakima HD crossbars. This crossbar length is the shortest length that is compatible with your vehicle. Unfortunately, this means that if your vehicle is not fit guided for a Yakima ladder rack with 60" HD crossbars, part # Y01157, you will not be able to size down.

I have included product description links and a video review link below.

expert reply by: Mark Smith

1

Answer 1

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 2

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 3

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Can I Use Shorter HD Crossbars On My Yakima OverHaul HD For My 2015 Toyota Tacoma

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching