Is The Pace Edwards Contractor Ladder Rack Compatible With The BAK Revolver X4 Tonneau Cover

Question

Question:

Revolver x4 mounts are inside the bed. Is there enough bed rail room for this rack to be installed if the stake pockets are fully exposed? For a 2018 F250.

asked by: Jeremy

0

Expert Reply:

The Pace Edwards Contractor Rig Rack Truck Bed Ladder Rack - Aluminum # 311-CR3004 only fits tonneau covers with explorer series rails by sliding into the T-tracks so it will not have anything to attach to with your Revolver X4 tonneau cover # BAK99ZR. Instead you can install a ladder rack like the Adarac Pro Series Custom Truck Bed Ladder Rack - Aluminum - 500lbs # A4000952 which does mount inside of the stake pockets in your bed rails and will allow you to retain use of your Revolver X4 tonneau cover # BAK99ZR.

expert reply by: Kevin C

0

Explorer Series Rails
(click to enlarge)

Answer 1

The BakFlip tonneau cover part #BAK48330 that you referenced will do a great job keeping most of the water out of your truck bed, but it's not totally waterproof so there's a possibility water will still get in during a heavy downpour. It has…

view full answer...

Answer 2

We do have a ladder rack solution for your 2020 Ford F-350 Super Duty with the BAKFlip MX4, part #BAK48330 for short bed or #BAK48331 for long bed, but you are correct that the vast majority out there use a clamping system which makes them…

view full answer...

Answer 3

Usually ladder racks use the inside edge of the top of the bed site to attach to the vehicle, but luckily there are exceptions to that. The Thule TracRac SR is typically compatible with tonneau covers that mount to the inside edges of the truck bed.…

view full answer...

Answer 4

Yes, the Adarac Pro Series Custom Truck Bed Ladder Rack part #A4000952 will work on a 2019 Ford F-250 with BAKFlip MX4 Hard Tonneau Cover part #BAK48330. In fact, the Adarac Pro Series is actually the only ladder rack that will work with the BAKFlip…

view full answer...

Answer 5

The BAKFlip MX4 Hard Tonneau Cover #BAK48330 sits about 1-1/2" below the top of the bed rails on your 2022 Ford F-350 Super Duty short bed. Since this is really close to the height of your B&W Companion #BWRVK3370. Because of this I…

view full answer...

Answer 6

I went ahead and brought your issue to my contact at BAK about your BAK tonneau cover, and he confirmed that you can either trim the hose or shove it through the hole. He also recommended using silicone around the nipple to deter leakage.

view full answer...

Answer 7

What you're looking for is the Thule T-Rac Pro2 Truck Bed Ladder Rack w/ Cantilever #TH37005XT-EX. This is rated for 1,000 lbs and comes with the cantilever piece which is the extra crossbar that hangs over your 2023 Toyota Tacoma cab. This rack…

view full answer...

Answer 8

There's only one style of tonneau cover we can recommend that fits with the TracRac sliding ladder racks like the part #TH43002XT-781 that you have installed on your 2018 GMC Sierra 1500 6-1/2 foot bed. That's the BAK Revolver tonneaus like…

view full answer...

Answer 9

Yes, you can carry a 40ft extension ladder on your 2003 Dodge Ram 1500 with 6-1/2 ft bed using the Thule SR Sliding Ladder Rack, #TH43003XT-501EX. You will have about 6 ft of overhang on the front and back if you center the ladder on the ladder rack,…

view full answer...

Answer 10

You would have no problem setting your crossover style tool box on top of the rails of the B&W Custom Headache Rack #BWPUCP7522BA that you referenced. To allow the box to open though you'll need to move it towards the rear of the truck bed so…

view full answer...

Answer 11

Yes, a 2018 Ford F-250 can be flat-towed with all four wheels down behind a motorhome. However, if you have a 2WD model then there is a required drive shaft coupling (disconnect) which we do not offer. There are also certain procedures that will need…

view full answer...

Answer 12

The Pace Edwards UltraGroove and Explorer rails are very similar, with the main difference being the height of the rails; UltraGroove sit slightly higher than Explorer rails. While the T-slot channel does differ very slightly (see photo), they are…

view full answer...

Is The Pace Edwards Contractor Ladder Rack Compatible With The BAK Revolver X4 Tonneau Cover

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching