Will the Dexter Trailer Hub # 84656UC3-EZ Work with My 3,500 Pound Lippert Axle?

Question

Question:

Hello. I’ve a new Carson trailer with a lippert 3500# axle an ez lube hub. I would like to change the bolt pattern, and I’d like to know if this parts kit will work? 84656UC3-EZ Thanks.

asked by: Kelley M

0

Expert Reply:

Yes, if you are looking for a 6 on 5-1/2 bolt pattern, the # 84656UC3-EZ will work with your Lippert 3,500 pound axle.

expert reply by: Bob C

0

Answer 1

The axle tag reads LCI35 which indicates it's a 3,500 lb axle and in which case this is all we need to confirm the corrects hubs and brakes. The Dexter Nev-R-Adjust Electric Trailer Brake Kit part #23-468-469 and Dexter Trailer Hub and Drum…

view full answer...

Answer 2

Sure can! I found your 2022 Grand Design Imagine 2910BH came with Dexter 4400lb axles so for a spare you'd need Trailer Hub #8-407-5UC3-EZ. You'll want to pick up some grease #L11380 as well.

view full answer...

Answer 3

From the axle tag you provided (thank you!), you do indeed have a 4,400 pound Dexter axle. The only hub/drum we carry that is compatible is the Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ.…

view full answer...

Answer 4

I did some research and was unable to find the component listing for the hub assembly you referenced. The best way to find out what the components are would be to remove them and locate the numbers on the bearing and seal and race. I have attached a…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Will the Dexter Trailer Hub # 84656UC3-EZ Work with My 3,500 Pound Lippert Axle?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching