Replacement Extang Tonneau Cover Snaps

Question

Question:

need snaps for tonneau cover please help

asked by: Stephen P

0

Expert Reply:

I would be happy to try to help you. We only offer 2 different types of replacement snaps for the rails and one for the actual covers and they are all for Extang Tonneau Covers. The first type are the ones you were looking at and they are the Replacement Offset Snap Studs for Extang Classic Platinum Tonneau Covers item # EX7128. This style slides along frame rails and can be moved to adjust for fitment. I have attached a photo of the snap with the dimensions.

The second type is the Replacement Offset Snap Studs for Extang BlackMax Tonneau Covers item # EX2128. These fit the Blackmax covers and also come in a 4 pack Item # EX2128-4.

The Replacement Snaps Installation Kit for Extang Snap-On Tonneau Covers item # EX7028-2016 is what you would need if you had to repair some broken or missing snaps on the actual cover itself.

expert reply by: Jerred H

0

snaps
(click to enlarge)

Answer 1

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 2

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 3

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 4

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 5

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 8

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Answer 11

A #93 incandescent bulb has a single contact bayonet base, and there are a couple of options for LED bulbs that will replace these. You can choose a bulb that gives off either a warm or cool light; I have added a photo showing the difference between…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Replacement Extang Tonneau Cover Snaps

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching