Is the Awning Head Pictured the One I Will Receive?

Question

Question:

Is this awning head like the one picture or is it the newer style for one?

asked by: Zachary R

0

Expert Reply:

Yes, the Lippert Solera Power Awning Speaker Idler Head, Black item # LC342150 that is pictured is the one you will receive. I have linked a review video for the awning head to give you a better look.

expert reply by: Jerred H

0

Answer 1

I'm not seeing any actual Solera Awnings that are 5'9", which would be quite small for an awning that uses a gas strut. With that said, I can tell you exactly what you need to measure to determine which gas strut replacement you'll…

view full answer...

Answer 2

I called my contact at Ultra-Fab and asked about the weight capacity of the Steel Mini-Roller for Trailers and RVs, part #UF48-979022. They said there is no weight capacity listed because it is not designed to bear a constant weight. These are…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Is the Awning Head Pictured the One I Will Receive?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching