Replacement Hub with 5 on 5 Bolt Pattern Using LM67048 and LM11949 Bearings
Question:
Howdy! I have an order trailer. Probably homemade. It has a hub that is 5 on 5. The outer bearing is no. LM11949 or .750 and the inner is no. LM67048 or 1.25. Can you point me in the right direction to the correct hub? Thanks
asked by: Shayne R
Expert Reply:
I may have a solution for you to replace the bearings, but I'm not aware of a hub that uses these particular bearings and also has a 5 on 5 bolt pattern. Typically this bearing combination is found on smaller agricultural hubs.
Assuming your hubs are otherwise still in good working order you could simply swap in new bearings, races and grease seals. If you wanted to go that route then you'll need bearing # LM67048 with a race # LM67010 which have an inner diameter of 1.250 inches; then you can use the bearing # LM11949 with race # LM11910 which have an inner diameter of .750 inches.
If you can also provide the dimensions or a part number from your grease seal, I can try to locate a replacement seal for that as well.
Products Referenced in This Question
Replacement Race for LM11949 Bearing
- Trailer Bearings Races Seals Caps
- Races
- Standard Races
- 1.781 Inch O.D.
- Bearing LM11949
- Race LM11910
- 3000 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - LM11949
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- .750 Inch I.D.
- Bearing LM11949
- Race LM11910
- 3000 lbs Axle
- etrailer
more information >
Replacement Race for LM67048 Bearing
- Trailer Bearings Races Seals Caps
- Races
- Standard Races
- 2.328 Inch O.D.
- Bearing LM67048
- Race LM67010
- 5200 lbs Axle
- 6000 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - LM67048
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.250 Inch I.D.
- Bearing LM67048
- Race LM67010
- 5000 lbs Axle
- 6000 lbs Axle
- etrailer
more information >
Product Page this Question was Asked From
Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 5 - Pre-Greased
- Trailer Hubs and Drums
- Hub
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 5 Inch
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Article: Most Popular Wheel Bearings
- Q&A: Is There a 3,500 lb Axle That is 89 Inches Long With Idler Hubs With 5 on 5" Bolt Pattern
- Article: Trailer Tire Sizing
- Article: Printable Trailer Bolt Hole Pattern Template
- Q&A: Availability Of Trailer Idler Hub With 5 on 5 Bolt Pattern
- Q&A: Timbren 3500 lb Rated Axle-Less Suspension and Compatible Idler Hub for Home Made Trailer
- Q&A: Dexter Never Adjust Brakes Initial Adjustment on Tandem Axle Trialer
- Q&A: Parts Needed To Switch a 3,500LB Axle To 5 on 5" Idler Hubs on 5X8 Utility Trailer
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: Replacement Bearings and Seal for Freedom Axle 45264 Hub Assembly
- Article: Dexter Service Bulletin #014
- Q&A: How to Determine the Size of a Trailer Hub Assembly for Replacement
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: Trailer Wiring Diagrams