Are Grease Seals Supposed to Sit Flush With Inner Face of Trailer Hub
Question:
I think i screwed up when putting in the rear or inner grease seal from the BK kit i purchased. Does the seal just sit flush with the outer hub lip ??? When i set it it went deeper into the hub. Will i need to order a new one ? I would probably damage the seal trying to back it out
asked by: Donnie D
Helpful Expert Reply:
Ideally, you want the grease seal flush with the inside lip of the hub but as long as the seal itself is riding on the proper spot on the spindle. If the seal has been pushed in too far to ride along the proper shoulder on the spindle, we offer the replacement seals in a 2 pack as part # RG06-020.
Products Referenced in This Question
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.500 Inch I.D.
- 1.987 Inch O.D
- TruRyde
more information >
Product Page this Question was Asked From
Bearing Kit, L44649 Inner/Outer Bearings, 10-9 Seal
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649
- Race L44610
- 2200 lbs Axle
- etrailer
more information >
Continue Researching
- Shop: Kodiak Disc Brake Caliper - Dacromet - 3,500 lbs to 6,000 lbs
- Shop: etrailer Electric Trailer Brakes - 7" - Left/Right Hand Assemblies - 2,000 lbs
- Shop: Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 1.5'
- Shop: Kodiak Hydraulic Brake Hose - FIF and 90-Degree Male Fittings w/ Stainless Flares - 1.5'
- Shop: Kodiak Disc Brake Caliper - Stainless Steel - 3,500 lbs to 6,000 lbs
- Q&A: How To Find Correct Bearing Kit for EZ Loader Boat Trailer
- Shop: Loadstar ST215/75D14 Bias Trailer Tire with 14" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Shop: Loadstar ST205/75D14 Bias Trailer Tire with 14" White Wheel - 5 on 4-1/2 - Load Range C
- Q&A: Should Trailer Hub Grease Seals Be Driven Flush With Hub Bore
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Search Results: grease seal
- Video: Bearing Repacking and Grease Seals Installation
- Q&A: How to Confirm Correct Size of Grease Seal
- Q&A: Can a Trailer Grease Seal Be Pressed In Too Far Beyond Flush
- Q&A: How Far in a Trailer Hub Should the Grease Seal Go
- Q&A: How to Measure to Determine the Correct Grease Seal for a Trailer Spindle
- Search Results: 5.30 x 12 trailer tire
- Search Results: cotter pin
- Search Results: lug stud
- Search Results: grease seal 1019
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Search Results: l44649
- Video: Titan Brake Actuator - Surge Brake Actuator - T47457107K Review
- Search Results: l44649 kit
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Video: Review of Timken Lubricants Sealants Adhesives - Hi Temp Red Grease Disc Drum Brake - TMK79ZR
- Video: LubriMatic Wheel Bearing Grease Review
- Video: Review of LubriMatic Lubricants Sealants Adhesives - Prime Guard Wheel Bearing Grease - L11380
- Video: Remove and Reinstall a Trailer Hub Review
- Shop: Trailer Wiring