What Size Bolt is Needed For Replacement Foot Plate for Lippert 501096

Question

Question:

I ordered a 10 inch foot plate for a Lippert 501096. What size bolt is specified to use to mount this. My old foot plate and bolt are lying in northern Wyoming.

asked by: Rich W

1

Helpful Expert Reply:

The replacement foot plate for the Lippert 501096 is the Replacement Foot Plate for Lippert Power Gear Hydraulic Jack # LC359344, and according to Lippert this will require a Grade 8 3/4"-16 x 1-1/2 bolt.

I have added a link below to a video review for you to check out as well of the Lippert Power Gear Hydraulic Jack # LC359344.

expert reply by: Kyle S

1

Answer 1

The bolt does not come with the Replacement Foot Plate for Lippert Power Gear Hydraulic Jack #LC359344. I checked with Lippert, and while there isn't an OEM replacement bolt, they did say that the correct bolt was a Grade 8 3/4"-16 x 1-1/2…

view full answer...

Answer 2

The Replacement Foot Pad #LC324269 that you referenced uses (and includes) a threaded 7/16" bolt for mounting. The mounting hole itself is just about 1/2" in diameter.

view full answer...

Answer 3

For the 6-point Level-Up System by Lippert, I made a call to the manufacturer to ensure you would receive correct information. Lippert said that when you bolt the footpads to the jacks, you need to torque them to 132 ft-lb. They said to make sure to…

view full answer...

Answer 4

The exact replacement foot plate for the Level Up system you have is not available as a replacement. But you could use #LC314667. The issue is that it uses a smaller bolt than the Level Up foot. So you would have to use a 1/2 inch bolt that will…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

What Size Bolt is Needed For Replacement Foot Plate for Lippert 501096

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching