What Size Is The Bolt That Retains The Hydraulic Fluid On The Bottom Of Lippert Hydraulic Jack?

Question

Question:

there is a bolt that is on the lower part of the jack that holds in the fluid in . my bolt is missing. what is the size of this bolt? this bolt is above the foot plate.

asked by: Artr M

0

Expert Reply:

The bolt is size 1/2 - 13 x 1 1/4 Flange GR 8 YZN that holds the fluid in on the bottom of the Lippert Level Up Hydraulic Jack # LC26FR.

expert reply by: Bud M

0

Answer 1

I can confirm that the correct part for you is the Replacement Lippert Components Correct Track Weld-On Axle Hanger #LC303918. When I reached out to Lippert they told me this hanger measured exactly 4.93 inches long x 3 inches wide x 3.3 inches.

view full answer...

Answer 2

The Lippert Correct Track Hanger part #LC303918 was designed to be used with leaf springs that are 1-3/4 inches wide like you have. You would not need to use a spacer with your 1-3/4 inch wide springs.

view full answer...

Answer 3

The Optronics LED Mini Trailer Utility Lights #UCL13C2PG and #UCL13CPG are identical aside from the ends of the wires as you noted. I have attached review videos for both that you can check out. The part #UCL13C2PG has the 0.180 female barrels while…

view full answer...

Answer 4

Only solution would be with a new leg like part #LC26FR as the seal for your jack is not available.

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…

view full answer...

What Size Is The Bolt That Retains The Hydraulic Fluid On The Bottom Of Lippert Hydraulic Jack?

Featured Help Information

Miscellaneous Media

Continue Researching