What are the Hole Diameters of the CE Smith CE20015G?
Question:
What is the diameter of center hole? 1 3/4 ?
asked by: GARY B
Expert Reply:
I contacted CE Smith to verify the sizing, and the center hole on the # CE20015G is 7/16". They also verified the 4 holes around the edges are indeed 3/8" as well. The 1 3/4" is referring to the diameter of the axle and width of the leaf spring this can be used with.
If you are looking to replace your current U-Bolt plate with this, it is also a good idea to replace the U-Bolts as well. The CE Smith # CE15285GA will pair with this plate and get everything secured. This is a single U-Bolt though, so 4 will be needed to cover one axle.
Products Referenced in This Question
CE Smith Replacement U-Bolt w/ Nuts for 1-3/4" Round Axles - 3/8" Diameter - Galvanized
- Trailer Suspension Parts
- U-Bolts
- Boat Trailer
- Snowmobile Trailer
- 2000 lbs
- Round Axle - 1-3/4 Inch
- 3/8 Inch Diameter
- 4-13/16 Inch Long
- CE Smith
more information >
Product Page this Question was Asked From
U-Bolt Plate for 1-3/4" Diameter Axle, 1-3/4" Wide Spring - 3/8" Bolts - Galvanized
- Trailer Suspension Parts
- U-Bolt Plates
- Boat Trailer
- Snowmobile Trailer
- 2000 lbs
- Round Axle - 1-3/4 Inch
- 3/8 Inch Diameter
- CE Smith
more information >
Continue Researching
- Shop: U-Bolt Plate for 1-3/4" Diameter Axle, 1-3/4" Wide Spring - 3/8" Bolts - Galvanized
- Shop: CE Smith Replacement U-Bolt w/ Nuts for 1-3/4" Round Axles - 3/8" Diameter - Galvanized
- Video: CE Smith Trailer Suspension CE20015G Review
- Shop: Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 1-7/8" Ball - Bolt On - 2,000 lbs
- Search Results: led lights
- Search Results: led trailer tail light
- Search Results: led trailer light kit
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Shop: CE Smith Roller Bunks for Boat Trailers - 5 Rollers Each - 4' Long - 1,500 lbs - 1 Pair
- Shop: U-Bolt Plate for 1-3/4" Diameter Axle, 1-3/4" Wide Spring - 3/8" Bolts - Galvanized
- Shop: Roller Shaft with Pal Nuts for Boat Trailer Rollers - Zinc-Plated Steel - 6-1/4" x 1/2"
- Video: etrailer Trigger Latch Channel Tongue Trailer Coupler Review
- Video: etrailer Channel Tongue Trailer Coupler Review
- Video: Review of etrailer Straight Tongue Trailer Coupler - Standard Coupler - CT-2003-Z
- Q&A: Channel Mount Coupler with 1-7/8 inch Hitch Ball
- Q&A: Are There Any Replacement Parts for a Shelby Trailer Coupler
- Article: Trailer Tire Sizing
- Q&A: After How Many Years Should Trailer Tires Be Replaced
- Q&A: Replacement Bearings and Hub for Malone MicroSport Trailer
- Q&A: Replacement Leaf Spring to Replace Spring that Measures 21-3/8 inch
- Q&A: Wiring configuration for Atwood GC6AA-10E Water Heater
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Article: Trailer Wiring Diagrams
- Article: Most Popular Wheel Bearings
- Article: Where to Position the Trailer Axle?
- Article: How to Raise Your Travel Trailer Height
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: How to Measure a Trailer Axle