Where Does The Red Rocker Switch Wire Attach To When Installing SuperWinch LT2000?
Question:
I trying to use a winch to pull a platform on a mobile home ramp and not sure where to conect the little red cable that is on the racker shwich
asked by: Jose
Expert Reply:
When installing the Superwinch LT2000 ATV Winch # 1120210 on atv's or offroad vehicles, the red wire on the rocker switch typically connects to a wire that gets power only when the ignition switch is turned on. When using this winch on a trailer or other application that does not have an ignition switch, you can just run it to the positive terminal on the battery that it is connected to and install a toggle switch in between so that you can switch the winch on and off, then actually control it with the included remote. I attached a wiring diagram and video for you.
Product Page this Question was Asked From
Superwinch LT2000 ATV Winch - Wire Rope - Roller Fairlead - 2,000 lbs
- Electric Winch
- ATV - UTV Winch
- 1-Stage Planetary Gear
- 1.0 HP
- 1001 - 2000 lbs
- 11 - 20 lbs
- Slow - 0 to 4 fpm
- No Remote
- Wire Rope
- Superwinch
more information >
Continue Researching
- Video: Review of Bulldog Winch Power Lead Extension For ATV UTV Winch - BDW20304
- Shop: Bulldog Winch Power Lead Extension for ATV/UTV Winches - 6 Gauge - 12' Long
- Q&A: Where to Attach Red Rocker Switch Wire on Superwinch LT2000
- Shop: Superwinch LT2000 ATV Winch - Wire Rope - Roller Fairlead - 2,000 lbs
- Q&A: Installation of the Remote for the Superwinch LT2000
- Video: Superwinch LT2000 ATV Winch Installation - 2010 Kawasaki Mule
- Video: Superwinch Electric Winch - ATV - UTV Winch - 1120210 Review
- Shop: Superwinch ATV Handlebar Switch Upgrade Kit for LT2000 Utility Winch
- Q&A: Wire Gauge to Connect Superwinch LT2000 ATV Winch to Battery 25 Feet Away
- Video: Performance Tool Hook Probe Circuit Tester Review
- Shop: Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid
- Video: Review of Maxxair RV Vents and Fans - Roof Vent - MA00-04751KSX
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: How Do I Measure the Drop Distance on a Trailer Drop Axle?
- Article: Trailer Wiring Diagrams
- Search Results: 44649
- Video: Tekonsha T-One Vehicle Wiring Harness Installation - 2018 Jeep JL Wrangler
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Shop: etrailer Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 5,200 lbs to 7,000 lbs
- Shop: Trailer Wiring
- Search Results: 68149
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: winch
- Shop: Brake Controller
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: Solution for Squeaky/Noisy Trailer Suspension with Equa-Flex Equalizers
- Shop: Suspension Enhancement
Fletcher B.
4/8/2024
attached red wire directly to the positive post on the battery. the solenoid only clicked when activated. Tied red wire to cig lighter hot side solenoid did same thing only clicked Winch fine when I attached battery cables directly to neg and pos post. What am I doing wrong???