Grease Seal With 1.71 Inner Diameter, 2.62 Outer Diameter With Bearings LM48548 & L44649
Question:
1979 Tennessee boat trailer. Hub Grease seal measures 2.62 OD x 1.71 ID Do you have a grease seal. Bearing size inside is 48548. Outside bearing is 44649. If you don’t have seal do you have hub 5 lug x 4 1/2 that I can put new bearing and race seal in 2.56 seals
asked by: Michelle
Expert Reply:
We do have a grease seal that is almost exactly what you measured that should work for you, with the outer diameter being 0.06 inches off, which could very easily be explained by the amount of pressure put on the caliper. So it is very likely that what will work for you is the Grease Seal # 58846.
This seal has a 1.71 inner diameter and 2.56 outer diameter, and would be the only seal with dimensions close to what yours are. If you need bearings and races, we also have those:
- Trailer Hub Bearing # LM48548
- Replacement Race for LM48548 Bearing # LM48510
- Replacement Trailer Hub Bearing # L44649
- Replacement Race for L44643 and L44649 Bearings # L44610
There aren't any hubs available with that combination of bearings, so the only other option, if you are sure that you do have a spindle and hubs that require these specific parts, is a new axle or to have a new spindle welded on, which depends on how heavy your trailer is. I have added links below to our selection of spindles and axles if you do need to go that route.
Products Referenced in This Question
Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.719 Inch I.D.
- 2.565 Inch O.D.
- etrailer
more information >
Replacement Race for L44643 and L44649 Bearings
- Trailer Bearings Races Seals Caps
- Races
- Standard Races
- 1.980 Inch O.D.
- Bearing L44643
- Bearing L44649
- Race L44610
- 2000 lbs Axle
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - LM48548
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.375 Inch I.D.
- Bearing LM48548
- Race LM48510
- 2500 lbs Axle
- TruRyde
more information >
Product Page this Question was Asked From
Replacement Race for LM48548 Bearing
- Trailer Bearings Races Seals Caps
- Races
- Standard Races
- 2.563 Inch O.D
- Bearing LM48548
- Race LM48510
- 2500 lbs Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Article: Most Popular Wheel Bearings
- Q&A: What Size Socket Works with 1 Inch Spindle Castle Nut # 165686?
- Q&A: Is Sealant Required for the Replacement Rubber Grommet for RV Black Water Tanks
- Q&A: Recommended Solution for a Taller Toilet Floor Flange
- Q&A: Bearings and Races for 7,000 Pound Trailer Axle
- Q&A: Can Trailer Spindle Be Mounted Directly to Trailer Frame Instead of Axle
- Q&A: Solution for 2,200 lb Axle with Short Spindles to Replace Hubs with 5 Lug Bolt Pattern
- Q&A: Replacement Hub/Drum Assembly Needed for a Dexter 8-147 Assembly
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Trailer Wiring Diagrams
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Where to Position the Trailer Axle?
- Article: Brake Controller Installation: Starting from Scratch