Comparing Curt And Draw-Tite Trailer Hitch Receivers for 2021 Audi Q5
Question:
I have a 2021 Audi Q5. Will get either Curt Class III 13331 or a Draw-Tite Class III 76183. 1 Your suggestion on which to use and why? 2 The Curt is designed to allow the Audi Bumper Beam and Cross Bar to be reinstalled over it. The Draw-Tite does not allow for the Audi Bumper Beam and Cross Bar to be reinstalled. They say the trailer bar replaces the Audi Bumper Beam. How is this so? It is not as deep or as long. Is it equal to or greater in strength to the Audi-designed bumper? 3 Since the Audi Bumper Beam is not re-installed with the Draw-Tite, is their cross bar larger and/or thicker than the Curt bar? I am trying to determine what the Draw-Tite advantage is over the Curt if the Draw-Tight does not allow for the factory bumper to be replaced. Should I be concerned? 4 I will pull a light boat and will hang a 2-bike tray-rack. Will the bike tray require stabilization straps with either one of these hitches? Thanks.
asked by: Bill L
Expert Reply:
I would be happy to make a recommendation for a trailer hitch for your 2021 Audi Q5.
Between the Curt Trailer Hitch Receiver # C13331 and Draw-Tite Max-Frame Trailer Hitch Receiver # 76183 I recommend the Curt # C13331 due to it allowing the rear bumper beam structure to be reinstalled for extra strength in the rear of the vehicle, and requiring less modifying to the rear bumper fascia.
Draw-Tite has mentioned that in their testing that with their hitch installed the bumper beam structure is not required due to the strength hitch being equal or greater than with the bumper beam installed, but personally I like that the Curt # C13331 allows it to be reinstalled. I was unable to find if the Draw-Tite # 76183 is thicker or larger than the # C13331.
Both options will be plenty strong to pull either you light boat trailer or 2-bike rack, and neither option will require the use of a stabilizing strap.
To complete your towing setup you will also need a vehicle wiring harness # 119250KIT, and if your boat trailer has surge brakes with an electric lockout you will also need the Curt Trailer Connector Adapter # C57187.
Lastly you will need a ball mount, hitch ball, and hitch pin and clip which can all be found in the etrailer Ball Mount Kit # 989900.
I included videos for each of the products mentioned for you to take a look at.
Products Referenced in This Question
ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Universal Fit
- 4 Flat
- Tekonsha
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt Trailer Connector Adapter - 4-Way Flat to 5-Way Flat - Vehicle End
- Trailer Wiring
- Wiring Adapters
- Single-Function Adapter
- 4 Flat
- Plug and Lead
- 5 Flat
- CURT
more information >