Recommended 2 Inch Ball Mount With 1 Inch Rise
Question:
Hi There - I am looking for a hitch ball mount that has 1 of rise and can accommodate a 2 5/16 ball. What products do you recommend for this?
asked by: Tyler
Expert Reply:
For a 2 inch ball mount that offers a 1 inch rise/2 inch drop and a 12K capacity, I'd recommend the Draw-Tite # 4284. For a 2-5/16 inch ball, use # 19286 which also has a 12K capacity.
If you don't need that much capacity, go for the Curt # C45030 and for a 2-5/16 inch ball, use # 63847. This combination would have a 7500 lb maximum capacity.
For either setup, you'd also need a # PC3 hitch in.
Products Referenced in This Question
2-5/16" Hitch Ball - 1-1/4" Diameter x 2-3/4" Long Shank - Chrome - 12,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-3/4 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 12000 lbs GTW
- Class IV
- Class V
- Draw-Tite
more information >
Draw-Tite Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 12" Long - 12,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1-1/4 Inch Ball Hole Diameter
- Steel Shank - Silver
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 12000 lbs GTW
- Class IV
- Long Shank
- Draw-Tite
more information >
2-5/16" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Article: Trailer Maintenance Schedule
- Q&A: Recommended Hitch for a 2024 Honda Pilot
- Q&A: Is Curt T-Connector Vehicle Wiring Harness For 2024 Honda Pilot a Curt Part
- Q&A: Replacement Trailer Jack for Shelby Model 5764A on Boat Trailer
- Q&A: How to Tell if 2020 Kia Sorento Has Factory Tow Package
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Bearing/Race/Seal Kit for Boat Trailer w/ NOK AD7131E Seal 25580 Inner and LM67048 Outer Bearing
- Q&A: What Size Sockets Do I Need to Install the etrailer Hitch e23ZR?