Could JTs Strongarm Kit be Installed on Trailer with 56-3/4 inches between Scissor Jacks

Question

Question:

Will the JTs Strong Arm Jack Stabilizer Kit for Travel Trailers work on a narrow-body trailer where the center-to-center distance between the scissor jacks is 56.75-inches?

asked by: Steven D

0

Expert Reply:

Yes the JTs Strongarm kits like # LC191025 could be used on a narrower frame width trailer frame like yours that has 56-3/4 inches between scissor jacks.

expert reply by: Jameson C

0

Answer 1

Yes, the JT's Strong Arm Jack Stabilizer Kit for Travel Trailers #LC191025 can be used on electric stabilizers. The Electric Stabilizer Jack Pad Adapter #LC314597 will allow you to attach the Strong Arms to the jack pad. These adapters can be…

view full answer...

Answer 2

The bar holding up your water tank wouldn't be a useable crossmember since it's just there to hold the tank up and isn't as structurally sound as an actual frame beam to handle to pressure the JT's Strong Arm Jack Stabilizer Kit…

view full answer...

Answer 3

I went our to the warehouse to measure the eye to eye distance on the arms of the JT's Strong Arm Jack Stabilizer Travel Trailer Kit #LC191025. From the center of one eye to the center of the other it was exactly 26 inches.

view full answer...

Answer 4

I went out to the warehouse to measure the length of the arms when extended for the JT's Strong Arm Jack Stabilizer Kit #LC191025. From the center of the hole on one end to the center of the hole on the other end it measures 46 inches extended.…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 11

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Could JTs Strongarm Kit be Installed on Trailer with 56-3/4 inches between Scissor Jacks

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching