How to Measure to Find Correct Grease Seal for Hub With Inner Bearing L44649 & Outer Bearing L44643
Question:
Hello, I have an older Nissan trailer with a hub marked W-2 with a 262 and 280 stamped on it. 5 bolt pattern, threaded holes. Inner bearing is L44649, outer L44643. I cannot find a seal number. Curious if you can cross reference any of these. Thanks
asked by: Randall H
Helpful Expert Reply:
I was unable to locate any hub with those numbers, so in order to find the correct grease seal, what you'll need to do is measure. To get the measurement, use digital caliper and measure your spindle to the thousandths of an inch where the grease seal rides like in the accompanying photo.
For a hub with inner bearing # L44649 and outer bearing # L44643 and a 5 on 4-1/2" bolt pattern, you will likely need the Dexter Trailer Idler Hub for 2,000-lb and 2,200-lb Axles # 8-259-50.
This hub is compatible with Grease Seal # 34823 (1.249" inner diameter) or Grease Seal # 10-9 (1.500" inner diameter).
If not, I have also added links below to our entire selection of hubs and bearings and seals for you should you need something else.
Products Referenced in This Question
Double Lip Grease Seal - ID 1.249" / OD 1.983" - Qty 1
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.249 Inch I.D.
- 1.983 Inch O.D.
- TruRyde
more information >
Dexter Trailer Idler Hub for 2,000-lb and 2,200-lb Axles - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Hub
- Standard
- L44643
- L44649
- L44643
- L44649
- For 2000 lbs Axles
- For 2200 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- Dexter
more information >
Replacement Trailer Hub Bearing - L44643
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.000 Inch I.D.
- Bearing L44643
- Race L44610
- 2000 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Product Page this Question was Asked From
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.500 Inch I.D.
- 1.987 Inch O.D
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Article: Most Popular Wheel Bearings
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Tire TLC: How & When to Check Your RV/Trailer Tire Pressure
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Q&A: Can the Dutton-Lanison Drill Drive Socket Adapter Be Used to Raise/Lower the Roof On a Jayco Pop Up
- Q&A: How To Figure Out the Correct Replacement Hubs for EZ Loader Boat Trailer
- Q&A: Replacement Grease Seal 4410275 For Shoreland'r Boat Trailer
- Q&A: Cross Referencing 10-9 Replacement Grease Seals for Aliner Trailer
- Q&A: Where to Find The Axle Serial Number On Dexter Axles Manufactured After April 2001?
- Q&A: Replacment Motor for Pump Assembly on Lippert LCI Pump 650057
- Q&A: How To Determine Which Bearing Kit Is Correct For 1984 EZ Loader M522000 Boat Trailer