Puck Covers for Ram OEM Rail Kit

Question

Question:

Hi I am missing some covers for my 2013 RAM puck system. Can you help direct me to what I should order? Thank you.

asked by: Gerri

1

Helpful Expert Reply:

We have the Draw Tite puck covers part # 58199 which do fit as covers for the Ram OEM rail kits like you have in your 2013 Ram 3500.

expert reply by: Jameson C

1

Answer 1

Reese Elite Made their puck system to match the the OEM version, you can use Replacement Puck Plug Covers for Elite and Signature Series Fifth Wheel Rails part #58199 to cover the holes. You will need Rubber Hole Cover for Reese Elite Series…

view full answer...

Answer 2

Curt Q25 5th Wheel Trailer Hitch for Ram Towing Prep Package, part #C16049, uses a spring-loaded locking dual jaw system to tightly grip your trailer's king pin, as shown in the linked video. The jaws themselves are between 1/2-inch and 3/4-inch…

view full answer...

Answer 3

Between the two, I recommend the Curt A25 #C16046 over the Q24 #C16545-16021. Both are great fifth wheel hitches that are compatible with your truck and would certainly fit your needs for hauling commercial campers. They are both made for trucks with…

view full answer...

Answer 4

On the B&W Companion OEM 5th Wheel Hitch for Ram Towing Prep Package - Dual Jaw - 25,000 lbs #BWRVK3600, the moving components of the locking jaws need to be lubed but the pin does not need lube. These jaws are the only part of the hitch that…

view full answer...

Answer 5

Yes, we certainly do have covers for the OEM puck system on your 2016 Ram 2500. For the center gooseneck hitch ball location you will need part #RP30136 and for the safety chain or 5th wheel hitch locations you will need two of the Replacement Puck…

view full answer...

Answer 6

It is a little strange that you are experiencing more chucking with a cushioned dual-jaw hitch that you were with a slide bar hitch with an non-cushioned head. But it could be because the head of the Q16 pivots on a large pin and could be moving a…

view full answer...

Answer 7

Since you mentioned the cotter pins which are used to secure the feet inside the rails, that makes me that you are referring to the connection point between the rail and foot on one of the four corners of the Curt A20 5th Wheel Trailer Hitch part…

view full answer...

Answer 8

It sounds like there may be something mechanically wrong with the Curt hitch #C16541. If the trailer king pin ever rested on top of the jaws or it was locked and the king pin ran into them it could have damaged something and now it is behaving in…

view full answer...

Answer 9

I spoke to my contact at Curt about your Curt A20 5th Wheel Trailer Hitch part #C16140 and they informed me that the locking handle issue is likely a result of improper lubrication. For starters, I would take some brake parts cleaner and spay down…

view full answer...

Answer 10

There is going to be a bit of movement with the kingpin inside of the locking jaws on the B&W Companion OEM 5th Wheel Trailer Hitch part #BWRVK3370 as it does need to rotate while turning but there aren't any adjustments for this. That said,…

view full answer...

Answer 11

If you are talking about adjusting the height of your 5th wheel hitch like the Curt A20 #C16140 then you will simply need to move the hitch head to the appropriate adjustment holes (see attached picture). Loosen the nuts on the bolts holding the…

view full answer...

Answer 12

I reached out to my contact at Curt and he said the most common cause for the issue you're experiencing with the handle on your A16 5th Wheel Hitch #C16521 is that the handle mechanism (referred to as the "pawl" in the owner's…

view full answer...

Puck Covers for Ram OEM Rail Kit

Products Referenced in This Question

Continue Researching