RV Air Conditioner Replacement Recommendation for RV with Coleman Setup

Question

Question:

I need an air conditioner asap, I was wondering if there was a unit available that was compatible with replacing a Coleman Mach and ready to ship right away. I have a duct system and wall thermostat, would appreciate any input.

asked by: Michael J

1

Helpful Expert Reply:

The Furrion Chill part # FR82PV is available and is designed for an easy replacement of a Coleman setup like you have as it's wiring will attach directly to allow you to use current controls and thermostat.

expert reply by: Jameson C

1

Answer 1

We have what you are looking for. Furrion Chill Replacement RV Air Conditioner for Coleman Setup - 13,500 Btu - White #FR82PV. You can reuse your current coleman components with this AC unit. It comes with the required wire adapter to use with your…

view full answer...

Answer 2

Yes. Furrion Chill Replacement RV Air Conditioner for Coleman Setup - 13,500 Btu - White #FR82PV. This unit can be used to replace a Coleman AC unit. It comes with the needed hardware and wire adapter.

view full answer...

Answer 3

The RVP air conditioner model 8333D876 is a Coleman Mach 3 according to my research. With that said, you can use Furrion Chill Replacement RV Air Conditioner for Furrion Setup part #FR86PR with the wiring adapter part #C-FACR15SA-A01 to hook up the…

view full answer...

Answer 4

From you email, I think you are asking for a recommendation for a replacement RVP air conditioner which is no longer manufactured. The RVP series is effectively a Coleman Mach air unit under a different label. This means they will have the same…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

RV Air Conditioner Replacement Recommendation for RV with Coleman Setup

Product Page this Question was Asked From

Continue Researching