Replacement Brake Assembly, Bearings, Races, and Seal for Old Trailer Axle
Question:
Hi Team so i have the following trailer see picture. i would like to get electronic brakes for it. i would like to replace the hub/drum and the brake assemblies but not the axle and not the wheels. the axle is about 2 1/8 in diameter and has a 5 bolt pattern to mount the brake assembly the bolts are spaced ~ 2 1/16 im assuming thats standard. the spindle has following measurements measured on the spindle Inner bearing ~1.5 in Outer bearing ~ 15/16 in. 0.9375 bower 1779 Inner grease seal ~ 1 7/8 1.875 trestle 300-156-6F outer grease seal is a plate on the nut thread my current brake assembly is 12 in from brake pad to brake pad but the pads are only 1 6/8 in deep. the hub/drum has 6 on 5-1/2 lug nut pattern. the lug nut pattern i would very much like to keep so i can keep my 16in wheels the trailer is rated for 3000 lbs on paper but is way beefier so i dont know if a 10in assembly would be enough. but i have not found one that mounts on 5 bolts.
asked by: Kelian
Expert Reply:
Based on the bolt pattern and the brake flange on your axle, you will want to start with the Electric Trailer Brake Kit - Self-Adjusting - 12" - Left and Right Hand Assemblies - 5.2K to 7K # AKEBRK-7-SA. Then for your hub drums I recommend reusing your current hubs as we don't have a suitable replacement and using bearings # 2788 and # 1779. Then for a seal I believe # 29031 is the correct fit. If you want to replace the races inside the hub use # 2729 and # 1729 along with the installation tool # PTW83020.
Products Referenced in This Question
Replacement Trailer Hub Bearing - 1779
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- .938 Inch I.D.
- Bearing 1779
- Race 1729
- 5200 lbs Axle
- etrailer
more information >
Replacement Race for 2788 Bearing
- Trailer Bearings Races Seals Caps
- Races
- Standard Races
- 3.000 Inch O.D.
- Bearing 2788
- Race 2729
- 5200 lbs Axle
- Redline
more information >
Replacement Trailer Hub Bearing - 2788
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.500 Inch I.D.
- Bearing 2788
- Race 2729
- 5200 lbs Axle
- etrailer
more information >
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Single Lip
- 1.875 Inch I.D.
- 3.000 Inch O.D.
- Redline
more information >
etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 12 x 2 Inch Drum
- 5200 lbs Axle
- 6000 lbs Axle
- 7000 lbs Axle
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- etrailer
more information >
7-Piece Installation Set for Bearings, Races, and Seals
- Accessories and Parts
- Trailer Bearings Races Seals Caps
- Tools
- Driver
- Performance Tool
more information >
Product Page this Question was Asked From
Replacement Race for 1779 Bearing
- Trailer Bearings Races Seals Caps
- Races
- Standard Races
- 2.240 Inch O.D.
- Bearing 1779
- Race 1729
- 5200 lbs Axle
- etrailer
more information >
Continue Researching
- Article: Most Popular Wheel Bearings
- Q&A: Replacement Bearings 2788 and 1779
- Q&A: Possible Replacement for Trostel 300-156-6 Seal
- Q&A: Bearings For Older Trailer Hub 22834
- Q&A: Replacement 1779 and 2788 Bearings and National 5970 Seal
- Q&A: How to Find Replacement for Hadco 322 Hubs
- Q&A: Trailer Hub Dust Cap with a 2.125" Outside Diameter
- Q&A: Recommended Tire Size for Upgrading Tires From 7.00-15LT on My Horse Trailer
- Article: Snow Tire Chain Overview: How to Buy the Right Tire Chains
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Double-Eye Trailer Suspension System Review
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer